Today's Message Index:
----------------------
1. 05:58 AM - Lord Adhesive Applicator Gun (LarryRosen)
2. 06:05 AM - Re: Lord Adhesive Applicator Gun (Michael Gregory)
3. 03:11 PM - GDU-460 display unit Test (Carlos Trigo)
4. 03:36 PM - Re: GDU-460 display unit Test (Stein Bruch)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Lord Adhesive Applicator Gun |
About to install my windows. Anyone interested in lending, renting or selling
their lord adhesive applicator gun? N205EN at gmail
--------
Larry Rosen
#40356
N205EN (reserved)
<http>
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=469081#469081
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Lord Adhesive Applicator Gun |
Larry,
I can lend you mine.
Just send me your address.
-Mike Gregory
On Sun, May 7, 2017 at 8:57 AM, LarryRosen <N205EN@gmail.com> wrote:
>
> About to install my windows. Anyone interested in lending, renting or
> selling their lord adhesive applicator gun? N205EN at gmail
>
> --------
> Larry Rosen
> #40356
> N205EN (reserved)
> <http>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=469081#469081
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | GDU-460 display unit Test |
Question for those RV-10'ers who have installed Garmin G3X
I've been installing a G3X system in an RV-10. Back in 2016 I bought
everything except the display units, and have been installing all the boxes
and circuits.
The installation is not yet completed, I still have some engine sensors to
be connected (CHT's and EGT's), but I already completed the CAN Bus and all
RS-232 connections.
Last week I bought one display unit (GDU-460), which arrived yesterday, and
you know how "boys and their toys" are: I immediately made some connections
to test the Display unit in the system.
When I turned the unit On, I only got Map and Charts information.
I was not able to see any Engine Information page in the display unit, nor
any Flight Instruments information or Attitude page, or any Auto-pilot
information.
So the question is:
* Why am I not getting the Engine page, or the Attitude page in the
display unit?
Could it be because the CAN Bus is open in the second Display unit?
(Remember, I still don't have the second display unit)
Could it be because the Roll servo (which is installed in the Right wing) is
still disconnected? (I still don't have the wings installed in the fuselage)
Could it be because some Engine sensors are still not connected to the
GEA-24?
Could it be for any other reason?
Best
Carlos
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | GDU-460 display unit Test |
You have a lot of work to do.you need to read the manual and go through all
the setup/configurations whilst ensuring everything is properly connected.
There are lots of reasons you might not be seeing things from configuration
settings to not having stuff hooked up (that is a must before you start
messing around with settings), etc..
If your dealer is experienced with G3X installs they should be able to walk
you through it easily!
Cheers,
Stein
From: owner-rv10-list-server@matronics.com
[mailto:owner-rv10-list-server@matronics.com] On Behalf Of Carlos Trigo
Sent: Sunday, May 07, 2017 5:11 PM
Subject: RV10-List: GDU-460 display unit Test
Question for those RV-10'ers who have installed Garmin G3X
I've been installing a G3X system in an RV-10. Back in 2016 I bought
everything except the display units, and have been installing all the boxes
and circuits.
The installation is not yet completed, I still have some engine sensors to
be connected (CHT's and EGT's), but I already completed the CAN Bus and all
RS-232 connections.
Last week I bought one display unit (GDU-460), which arrived yesterday, and
you know how "boys and their toys" are: I immediately made some connections
to test the Display unit in the system.
When I turned the unit On, I only got Map and Charts information.
I was not able to see any Engine Information page in the display unit, nor
any Flight Instruments information or Attitude page, or any Auto-pilot
information.
So the question is:
* Why am I not getting the Engine page, or the Attitude page in the
display unit?
Could it be because the CAN Bus is open in the second Display unit?
(Remember, I still don't have the second display unit)
Could it be because the Roll servo (which is installed in the Right wing) is
still disconnected? (I still don't have the wings installed in the fuselage)
Could it be because some Engine sensors are still not connected to the
GEA-24?
Could it be for any other reason?
Best
Carlos
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|