---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Wed 07/12/17: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 08:20 AM - Van's FWF kit (whodja) 2. 08:22 AM - Van's FWF kit (whodja) 3. 02:59 PM - Re: Van's FWF kit (tsts4) 4. 04:50 PM - Re: Rv10 yaw damper (woxofswa) 5. 08:11 PM - Re: Van's FWF kit (Lenny Iszak) ________________________________ Message 1 _____________________________________ Time: 08:20:44 AM PST US Subject: RV10-List: Van's FWF kit From: "whodja" I've read numerous posts regarding different options when installing the engine. Does anyone know of a list of recommendations for items to delete from the Van's FWF kit. I'm installing the IO-540 from Lycoming with 1 slick and 1 pmag. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=470938#470938 ________________________________ Message 2 _____________________________________ Time: 08:22:18 AM PST US Subject: RV10-List: Van's FWF kit From: "whodja" I've read numerous posts regarding different options when installing the engine. Does anyone know of a list of recommendations for items to delete from the Van's FWF kit. I'm installing the IO-540 from Lycoming with 1 slick and 1 pmag. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=470939#470939 ________________________________ Message 3 _____________________________________ Time: 02:59:04 PM PST US Subject: RV10-List: Re: Van's FWF kit From: "tsts4" Its been awhile but IIRC I deleted most of the hoses (which I replaced with ones from Tom at TS Flightlnes), the alternator, and the oil cooler mount/bracket (which I had bought earlier so I could install it during firewall construction). -------- Todd Stovall aka Auburntsts on EAA, AOPA, and VAF RV-10 N728TT -- Flying Read this topic online here: http://forums.matronics.com/viewtopic.php?p=470957#470957 ________________________________ Message 4 _____________________________________ Time: 04:50:15 PM PST US Subject: RV10-List: Re: Rv10 yaw damper From: "woxofswa" https://photos.app.goo.gl/XGkzgT9ONmZDAFB33 Unless I just have an anomaly, I may have discovered the mysterious reason that "slight modification" must be done to use the 14 designated Y/D bracket kit on a -10. The Y/D bracket is supposed to sandwich in-between the pitch servo bracket and the flange of the bulkhead which are already mated up. The two aft holes, however, are about 1/16 of an inch wider on the Y/D bracket forcing you to elongate the hole inward to match up. Considering the absolute deadnuts accuracy there has been in everything else, I have to imagine that they know this. It is too far off to fit but close enough for the screw to barely catch a thread or two. A simple note in the instructions could save some tailcone imbedded frustration and perhaps, a stripped nutplate that would be a bugger to replace. -------- Myron Nelson Mesa, AZ Flew May 10 2014 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=470959#470959 ________________________________ Message 5 _____________________________________ Time: 08:11:30 PM PST US Subject: RV10-List: Re: Van's FWF kit From: "Lenny Iszak" I'd delete the Pmag and move on to something that's actually available. :) It was ready to ship within the next two weeks at least 7 years ago. If you are going with the stock Lycoming, Van's cowling, Hartzell prop then the fwf kit is adequate. I upgraded all the hoses to integral firesleeve from Stratoflex. If I were to do it again I'd get the fuel hoses with the red external firesleeve on it. It may keep the fuel inside the hose a bit cooler. Also, delete the hose that's connecting the fuel injection servo and the spider and get two shorter ones to connect the fuel flow sender in between there. Lenny whodja wrote: > I've read numerous posts regarding different options when installing the engine. Does anyone know of a list of recommendations for items to delete from the Van's FWF kit. I'm installing the IO-540 from Lycoming with 1 slick and 1 pmag. -------- Lenny Iszak Palm City, FL 2014 RV-10, N311LZ - 300 hrs Read this topic online here: http://forums.matronics.com/viewtopic.php?p=470964#470964 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.