Today's Message Index:
----------------------
1. 05:54 AM - Re: Need latest Navworx UAT Console (Rob Kermanj)
2. 06:32 AM - Re: Need latest Navworx UAT Console (Ralph E. Capen)
3. 06:57 AM - Re: Need latest Navworx UAT Console (Rob Kermanj)
4. 07:01 AM - Re: Cleveland Wheel Bearings (Bill Watson)
5. 07:06 AM - Re: Need latest Navworx UAT Console (Bob Leffler)
6. 07:51 AM - Re: Cleveland Wheel Bearings (David Saylor)
7. 08:04 AM - Re: Need latest Navworx UAT Console (Rob Kermanj)
8. 01:54 PM - Re: Need latest Navworx UAT Console (Bob Leffler)
9. 03:54 PM - Re: Need latest Navworx UAT Console (Rob Kermanj)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Need latest Navworx UAT Console |
Does anyone know if AMCO applies to Avidyne ID-540?
Thanks.
> On Nov 2, 2017, at 9:38 AM, Bob Leffler <bob@thelefflers.com> wrote:
>
> If you need 4.1.0 and the manual, let me know.
>
> I haven=99t been able to locate anyone that has 5.0 yet.
>
> Get Outlook for iOS <https://aka.ms/o0ukef>
> From: owner-rv10-list-server@matronics.com
<mailto:owner-rv10-list-server@matronics.com>
<owner-rv10-list-server@matronics.com
<mailto:owner-rv10-list-server@matronics.com>> on behalf of Bill Watson
<Mauledriver@nc.rr.com <mailto:Mauledriver@nc.rr.com>>
> Sent: Thursday, November 2, 2017 11:01:53 AM
> To: rv10-list@matronics.com <mailto:rv10-list@matronics.com>
> Subject: RV10-List: Need latest Navworx UAT Console
>
<mailto:Mauledriver@nc.rr.com>>
>
> I have the Navworx unit that will work with the AMOC given a certified
> GPS source. But I don't have a copy of the UAT console that will run,
> looking for help.
>
> I tried running the UAT console software I obtained back in 2012 but
get
> an error on loading, "Nonshared DATA segment required", then if fails
to
> open. Anyone have experience with this?
>
> A secondary concern I have is that I recall the UAT console loads a
> version of the Navworx software. If so, this is backlevel for my box
> (my box had been sent in since then for a maintenance upgrade).
>
> Does anyone have a copy of the UAT console that they can share or
> otherwise advise? Thanks.
>
> (I'll be posting on the VAF board as well)
>
> Bill "wired up G430w to the deadend box with all appendages crossed"
Watson
>
>
> ---
> This email has been checked for viruses by Avast antivirus software.
> https://www.avast.com/antivirus <https://www.avast.com/antivirus>
>
> ==========
> Email Forum -
> -List">http://www.matronics.com/Navigator?RV10-List
<http://www.matronics.com/Navigator?RV10-List>
> ==========
> p; - MATRONICS WEB FORUMS -
> ums.matronics.com <http://ums.matronics.com/>
> ==========
> p; - NEW MATRONICS LIST WIKI -
> matronics.com <http://matronics.com/>
> ==========
> p; - List Contribution Web Site -
> p; -Matt Dralle, List Admin.
> http://www.matronics.com/contribution
<http://www.matronics.com/contribution>
> ==========
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Need latest Navworx UAT Console |
Rob,
The three AMOCS that have been approved are all for Garmin products.
That having been said, the most recent responses from the FAA indicate that they
may be open to approving other data sources that output the "ADS-B OUT+" protocol
as it contains the necessary data elements required for position reporting.
In my updated AMOC, they specifically reference the ADS-B OUT+ protocol.
If the Avidyne outputs it, you should be able to get approval...
I would suggest putting the AMOC together like we did - we can provide you with
what we submitted as a sample if you want...
Ralph
-----Original Message-----
From: Rob Kermanj
Sent: Nov 8, 2017 8:52 AM
Subject: Re: RV10-List: Need latest Navworx UAT Console
Does anyone know if AMCO applies to Avidyne ID-540?
Thanks.
On Nov 2, 2017, at 9:38 AM, Bob Leffler <bob@thelefflers.com> wrote:
If you need 4.1.0 and the manual, let me know.
I havent been able to locate anyone that has 5.0 yet.
Get Outlook for iOSFrom: owner-rv10-list-server@matronics.com <owner-rv10-list-server@matronics.com>
on behalf of Bill Watson <Mauledriver@nc.rr.com>
Sent: Thursday, November 2, 2017 11:01:53 AM
I have the Navworx unit that will work with the AMOC given a certified
GPS source. But I don't have a copy of the UAT console that will run,
looking for help.
I tried running the UAT console software I obtained back in 2012 but get
an error on loading, "Nonshared DATA segment required", then if fails to
open. Anyone have experience with this?
A secondary concern I have is that I recall the UAT console loads a
version of the Navworx software. If so, this is backlevel for my box
(my box had been sent in since then for a maintenance upgrade).
Does anyone have a copy of the UAT console that they can share or
otherwise advise? Thanks.
(I'll be posting on the VAF board as well)
Bill "wired up G430w to the deadend box with all appendages crossed" Watson
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
==========
Email Forum -
-List">http://www.matronics.com/Navigator?RV10-List
==========
p; - MATRONICS WEB FORUMS -
ums.matronics.com
==========
p; - NEW MATRONICS LIST WIKI -
matronics.com
==========
p; - List Contribution Web Site -
p; -Matt Dralle, List Admin.
http://www.matronics.com/contribution
==========
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Need latest Navworx UAT Console |
Ralph, thanks for the quick reply. Please send me the package you provided to
the FAA. I spoke to Avidyne and they researching it on their end. I will forward
your email (if OK with you) to Avidyne and a copy of my proposal to FAA so
they also remain in the loop.
Thanks again
Rob.
Sent from my iPhone
> On Nov 8, 2017, at 7:31 AM, Ralph E. Capen <recapen@earthlink.net> wrote:
>
>
> Rob,
>
> The three AMOCS that have been approved are all for Garmin products.
> That having been said, the most recent responses from the FAA indicate that they
may be open to approving other data sources that output the "ADS-B OUT+" protocol
as it contains the necessary data elements required for position reporting.
In my updated AMOC, they specifically reference the ADS-B OUT+ protocol.
If the Avidyne outputs it, you should be able to get approval...
>
> I would suggest putting the AMOC together like we did - we can provide you with
what we submitted as a sample if you want...
>
> Ralph
> -----Original Message-----
>
> From: Rob Kermanj
>
> Sent: Nov 8, 2017 8:52 AM
>
> To: rv10-list@matronics.com
>
> Subject: Re: RV10-List: Need latest Navworx UAT Console
>
>
>
> Does anyone know if AMCO applies to Avidyne ID-540?
> Thanks.
> On Nov 2, 2017, at 9:38 AM, Bob Leffler <bob@thelefflers.com> wrote:
> If you need 4.1.0 and the manual, let me know.
> I havent been able to locate anyone that has 5.0 yet.
> Get Outlook for iOSFrom: owner-rv10-list-server@matronics.com <owner-rv10-list-server@matronics.com>
on behalf of Bill Watson <Mauledriver@nc.rr.com>
> Sent: Thursday, November 2, 2017 11:01:53 AM
> To: rv10-list@matronics.com
>
> I have the Navworx unit that will work with the AMOC given a certified
> GPS source. But I don't have a copy of the UAT console that will run,
> looking for help.
>
> I tried running the UAT console software I obtained back in 2012 but get
> an error on loading, "Nonshared DATA segment required", then if fails to
> open. Anyone have experience with this?
>
> A secondary concern I have is that I recall the UAT console loads a
> version of the Navworx software. If so, this is backlevel for my box
> (my box had been sent in since then for a maintenance upgrade).
>
> Does anyone have a copy of the UAT console that they can share or
> otherwise advise? Thanks.
>
> (I'll be posting on the VAF board as well)
>
> Bill "wired up G430w to the deadend box with all appendages crossed" Watson
>
>
> ---
> This email has been checked for viruses by Avast antivirus software.
> https://www.avast.com/antivirus
>
> ==========
> Email Forum -
> -List">http://www.matronics.com/Navigator?RV10-List
> ==========
> p; - MATRONICS WEB FORUMS -
> ums.matronics.com
> ==========
> p; - NEW MATRONICS LIST WIKI -
> matronics.com
> ==========
> p; - List Contribution Web Site -
> p; -Matt Dralle, List Admin.
> http://www.matronics.com/contribution
> ==========
>
>
>
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Cleveland Wheel Bearings |
Request for background: What kind off experience have people had with
failing/damaged/rusting wheel bearings vis-a-vis maintenance of wheel
bearing?
I operate off a sometimes wet and mushy field where my wheels get quite
a dousing. Each condition inspection, I've been repacking the
bearings. So far I have seen any signs of rusting - is there something
else I should be looking for?
Bill "6 years and 900+ hours on same bearings, color me curious" Watson
On 11/7/2017 7:26 PM, David Saylor wrote:
> Does anyone have a good source for wheel bearings? I found Timken nose
> bearings for about $40 but the my shopping cart at Vans is running
> about $650 for all 8 pcs for the mains. I'm pretty sure it doesn't
> have to be this way. But my search for LM274949-2-629 is coming up
> short.
>
> Has someone had success with an alternate number? Besides the
> Cleveland number?
>
> Thanks,
>
> --Dave
>
>
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Need latest Navworx UAT Console |
The avidyne does indeed support adsb+
I can assist with writing the AMOC. It will literally take 5-10 minutes to
create the doc to send to the FAA
Email me if you want to go down that path.
Get Outlook for iOS<https://aka.ms/o0ukef>
________________________________
From: owner-rv10-list-server@matronics.com <owner-rv10-list-server@matronic
s.com> on behalf of Ralph E. Capen <recapen@earthlink.net>
Sent: Wednesday, November 8, 2017 9:31:07 AM
Subject: Re: RV10-List: Need latest Navworx UAT Console
Rob,
The three AMOCS that have been approved are all for Garmin products.
That having been said, the most recent responses from the FAA indicate that
they may be open to approving other data sources that output the "ADS-B OU
T+" protocol as it contains the necessary data elements required for positi
on reporting. In my updated AMOC, they specifically reference the ADS-B OU
T+ protocol. If the Avidyne outputs it, you should be able to get approval
...
I would suggest putting the AMOC together like we did - we can provide you
with what we submitted as a sample if you want...
Ralph
-----Original Message-----
From: Rob Kermanj
Sent: Nov 8, 2017 8:52 AM
Subject: Re: RV10-List: Need latest Navworx UAT Console
Does anyone know if AMCO applies to Avidyne ID-540?
Thanks.
On Nov 2, 2017, at 9:38 AM, Bob Leffler <bob@thelefflers.com> wrote:
If you need 4.1.0 and the manual, let me know.
I haven=92t been able to locate anyone that has 5.0 yet.
Get Outlook for iOSFrom: owner-rv10-list-server@matronics.com <owner-rv10-l
ist-server@matronics.com> on behalf of Bill Watson <Mauledriver@nc.rr.com>
Sent: Thursday, November 2, 2017 11:01:53 AM
Subject: RV10-List: Need latest Navworx UAT Console --> RV10-List message p
osted by: Bill Watson <Mauledriver@nc.rr.com>
I have the Navworx unit that will work with the AMOC given a certified
GPS source. But I don't have a copy of the UAT console that will run,
looking for help.
I tried running the UAT console software I obtained back in 2012 but get
an error on loading, "Nonshared DATA segment required", then if fails to
open. Anyone have experience with this?
A secondary concern I have is that I recall the UAT console loads a
version of the Navworx software. If so, this is backlevel for my box
(my box had been sent in since then for a maintenance upgrade).
Does anyone have a copy of the UAT console that they can share or
otherwise advise? Thanks.
(I'll be posting on the VAF board as well)
Bill "wired up G430w to the deadend box with all appendages crossed" Watson
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
Email Forum -
-List">http://www.matronics.com/Navigator?RV10-List
p; - MATRONICS WEB FORUMS -
ums.matronics.com
p; - NEW MATRONICS LIST WIKI -
matronics.com
p; - List Contribution Web Site -
p; -Matt Dralle, List Admin.
http://www.matronics.com/contribution
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Cleveland Wheel Bearings |
Right, SHC 100 looks a lot like Mobil 28 but it's lighter red IIRC. I used
it last year.
--Dave
On Tue, Nov 7, 2017 at 7:09 PM, Kelly McMullen <kellym@aviating.com> wrote:
>
> Once you get replacements, be aware that Cleveland has changed their
> grease recommendations. Aeroshell #5 is no longer 1st choice.
> First choice is Mobil SHC 100, which is a red synthetic grease.
> Skygeek carries an appropriate sized tube. The rest of suppliers, last I
> looked only carry 5 lbs and up.
> I do not know reason Cleveland changed their recommendation.
> Kelly
>
> On 11/7/2017 7:07 PM, Tim Olson wrote:
>
>>
>> Yeah I've taken them in to a local place in town before
>> called "Bearing Headquarters" and they can get just
>> about anything.
>> Tim
>>
>> On 11/7/2017 7:17 PM, Don Orrick wrote:
>>
>>>
>>> Local auto parts store can order them or a local bearing supply co can
>>> get them
>>>
>>> Sent from my iPhone
>>>
>>> On Nov 7, 2017, at 6:26 PM, David Saylor <saylor.dave@gmail.com> wrote:
>>>>
>>>> Does anyone have a good source for wheel bearings? I found Timken nose
>>>> bearings for about $40 but the my shopping cart at Vans is running about
>>>> $650 for all 8 pcs for the mains. I'm pretty sure it doesn't have to be
>>>> this way. But my search for LM274949-2-629 is coming up short.
>>>>
>>>> Has someone had success with an alternate number? Besides the
>>>> Cleveland number?
>>>>
>>>> Thanks,
>>>>
>>>> --Dave
>>>>
>>>>
>>>>
>>
>>
>
>
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Need latest Navworx UAT Console |
Thanks Bob. Yes ...please, please. What do you need from me?
Sent from my iPhone
> On Nov 8, 2017, at 8:05 AM, Bob Leffler <bob@thelefflers.com> wrote:
>
> The avidyne does indeed support adsb+
>
> I can assist with writing the AMOC. It will literally take 5-10 minutes t
o create the doc to send to the FAA
>
> Email me if you want to go down that path.
>
> Get Outlook for iOS
> From: owner-rv10-list-server@matronics.com <owner-rv10-list-server@matroni
cs.com> on behalf of Ralph E. Capen <recapen@earthlink.net>
> Sent: Wednesday, November 8, 2017 9:31:07 AM
> To: rv10-list@matronics.com
> Subject: Re: RV10-List: Need latest Navworx UAT Console
>
>
> Rob,
>
> The three AMOCS that have been approved are all for Garmin products.
> That having been said, the most recent responses from the FAA indicate tha
t they may be open to approving other data sources that output the "ADS-B OU
T+" protocol as it contains the necessary data elements required for positio
n reporting. In my updated AMOC, they specifically reference the ADS-B OUT+
protocol. If the Avidyne outputs it, you should be able to get approval...
>
> I would suggest putting the AMOC together like we did - we can provide you
with what we submitted as a sample if you want...
>
> Ralph
> -----Original Message-----
>
> From: Rob Kermanj
>
> Sent: Nov 8, 2017 8:52 AM
>
> To: rv10-list@matronics.com
>
> Subject: Re: RV10-List: Need latest Navworx UAT Console
>
>
>
> Does anyone know if AMCO applies to Avidyne ID-540?
> Thanks.
> On Nov 2, 2017, at 9:38 AM, Bob Leffler <bob@thelefflers.com> wrote:
> If you need 4.1.0 and the manual, let me know.
> I haven=99t been able to locate anyone that has 5.0 yet.
> Get Outlook for iOSFrom: owner-rv10-list-server@matronics.com <owner-rv10-
list-server@matronics.com> on behalf of Bill Watson <Mauledriver@nc.rr.com>
> Sent: Thursday, November 2, 2017 11:01:53 AM
> To: rv10-list@matronics.com
> Subject: RV10-List: Need latest Navworx UAT Console --> RV10-List message p
osted by: Bill Watson <Mauledriver@nc.rr.com>
>
> I have the Navworx unit that will work with the AMOC given a certified
> GPS source. But I don't have a copy of the UAT console that will run,
> looking for help.
>
> I tried running the UAT console software I obtained back in 2012 but get
> an error on loading, "Nonshared DATA segment required", then if fails to
> open. Anyone have experience with this?
>
> A secondary concern I have is that I recall the UAT console loads a
> version of the Navworx software. If so, this is backlevel for my box
> (my box had been sent in since then for a maintenance upgrade).
>
> Does anyone have a copy of the UAT console that they can share or
> otherwise advise? Thanks.
>
> (I'll be posting on the VAF board as well)
>
> Bill "wired up G430w to the deadend box with all appendages crossed" Watso
n
>
>
> ---
> This email has been checked for viruses by Avast antivirus software.
> https://www.avast.com/antivirus
>
> ==========
> Email Forum -
> -List">http://www.matronics.com/Navigator?RV10-List
> ==========
> p; - MATRONICS WEB FORUMS -
> ums.matronics.com
> ==========
> p; - NEW MATRONICS LIST WIKI -
> matronics.com
> ==========
> p; - List Contribution Web Site -
> p; -Matt Dralle, List Admin.
> http://www.matronics.com/contribution
> ==========
>
>
>
> ==========
> Email Forum -
> -List">http://www.matronics.com/Navigator?RV10-List
> ==========
> p; - MATRONICS WEB FORUMS -
> ums.matronics.com
> ==========
> p; - NEW MATRONICS LIST WIKI -
> matronics.com
> ==========
> p; - List Contribution Web Site -
> p; -Matt Dralle, List Admin.
> http://www.matronics.com/contribution
> ==========
>
>
>
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Need latest Navworx UAT Console |
Wire the Avidyne to the ads600-b using the adsb+ protocol.
I don=92t recall if there is an Avidyne example in the Navworx manual.
Use the gtn650/gns430w as an example. The gps pins will be different, but
the NavWorxs side will be the same.
Disconnect the internal gps antenna
Change the Navworx configuration to use the external gps
Validate that you have three green status indicators
Fly and get a copy of the public performance report from the FAA.
If there is an Avidyne schematic in the Navworx manual, we can cut and past
e that, if not you=92ll have to create an installation schematic. Again,
use the Garmin schematics as an example.
Then let me know. It=92s a simple cut and paste job using my application
as a template.
Get Outlook for iOS<https://aka.ms/o0ukef>
________________________________
From: owner-rv10-list-server@matronics.com <owner-rv10-list-server@matronic
s.com> on behalf of Rob Kermanj <flysrv10@gmail.com>
Sent: Wednesday, November 8, 2017 11:02:27 AM
Subject: Re: RV10-List: Need latest Navworx UAT Console
Thanks Bob. Yes ...please, please. What do you need from me?
Sent from my iPhone
On Nov 8, 2017, at 8:05 AM, Bob Leffler <bob@thelefflers.com<mailto:bob@the
lefflers.com>> wrote:
The avidyne does indeed support adsb+
I can assist with writing the AMOC. It will literally take 5-10 minutes to
create the doc to send to the FAA
Email me if you want to go down that path.
Get Outlook for iOS<https://aka.ms/o0ukef>
________________________________
From: owner-rv10-list-server@matronics.com<mailto:owner-rv10-list-server@ma
tronics.com> <owner-rv10-list-server@matronics.com<mailto:owner-rv10-list-s
erver@matronics.com>> on behalf of Ralph E. Capen <recapen@earthlink.net<ma
ilto:recapen@earthlink.net>>
Sent: Wednesday, November 8, 2017 9:31:07 AM
Subject: Re: RV10-List: Need latest Navworx UAT Console
ilto:recapen@earthlink.net>>
Rob,
The three AMOCS that have been approved are all for Garmin products.
That having been said, the most recent responses from the FAA indicate that
they may be open to approving other data sources that output the "ADS-B OU
T+" protocol as it contains the necessary data elements required for positi
on reporting. In my updated AMOC, they specifically reference the ADS-B OU
T+ protocol. If the Avidyne outputs it, you should be able to get approval
...
I would suggest putting the AMOC together like we did - we can provide you
with what we submitted as a sample if you want...
Ralph
-----Original Message-----
From: Rob Kermanj
Sent: Nov 8, 2017 8:52 AM
Subject: Re: RV10-List: Need latest Navworx UAT Console
Does anyone know if AMCO applies to Avidyne ID-540?
Thanks.
On Nov 2, 2017, at 9:38 AM, Bob Leffler <bob@thelefflers.com<mailto:bob@the
lefflers.com>> wrote:
If you need 4.1.0 and the manual, let me know.
I haven=92t been able to locate anyone that has 5.0 yet.
Get Outlook for iOSFrom: owner-rv10-list-server@matronics.com<mailto:owner-
rv10-list-server@matronics.com> <owner-rv10-list-server@matronics.com<mailt
o:owner-rv10-list-server@matronics.com>> on behalf of Bill Watson <Mauledri
ver@nc.rr.com<mailto:Mauledriver@nc.rr.com>>
Sent: Thursday, November 2, 2017 11:01:53 AM
Subject: RV10-List: Need latest Navworx UAT Console --> RV10-List message p
osted by: Bill Watson <Mauledriver@nc.rr.com<mailto:Mauledriver@nc.rr.com>>
I have the Navworx unit that will work with the AMOC given a certified
GPS source. But I don't have a copy of the UAT console that will run,
looking for help.
I tried running the UAT console software I obtained back in 2012 but get
an error on loading, "Nonshared DATA segment required", then if fails to
open. Anyone have experience with this?
A secondary concern I have is that I recall the UAT console loads a
version of the Navworx software. If so, this is backlevel for my box
(my box had been sent in since then for a maintenance upgrade).
Does anyone have a copy of the UAT console that they can share or
otherwise advise? Thanks.
(I'll be posting on the VAF board as well)
Bill "wired up G430w to the deadend box with all appendages crossed" Watson
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
Email Forum -
-List">http://www.matronics.com/Navigator?RV10-List
p; - MATRONICS WEB FORUMS -
ums.matronics.com<http://ums.matronics.com>
p; - NEW MATRONICS LIST WIKI -
matronics.com<http://matronics.com>
p; - List Contribution Web Site -
p; -Matt Dralle, List Admin.
http://www.matronics.com/contribution
Email Forum -
-List">http://www.matronics.com/Navigator?RV10-List
p; - MATRONICS WEB FORUMS -
ums.matronics.com<http://ums.matronics.com>
p; - NEW MATRONICS LIST WIKI -
matronics.com<http://matronics.com>
p; - List Contribution Web Site -
p; -Matt Dralle, List Admin.
http://www.matronics.com/contribution
Message 9
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Need latest Navworx UAT Console |
Thanks Bob. Will do. Will let you how it turns out.
Sent from my iPhone
> On Nov 8, 2017, at 2:52 PM, Bob Leffler <bob@thelefflers.com> wrote:
>
> Wire the Avidyne to the ads600-b using the adsb+ protocol.
>
> I don=99t recall if there is an Avidyne example in the Navworx manua
l.
>
> Use the gtn650/gns430w as an example. The gps pins will be different, bu
t the NavWorxs side will be the same.
>
> Disconnect the internal gps antenna
>
> Change the Navworx configuration to use the external gps
>
> Validate that you have three green status indicators
>
> Fly and get a copy of the public performance report from the FAA.
>
> If there is an Avidyne schematic in the Navworx manual, we can cut and pas
te that, if not you=99ll have to create an installation schematic. A
gain, use the Garmin schematics as an example.
>
> Then let me know. It=99s a simple cut and paste job using my appli
cation as a template.
>
> Get Outlook for iOS
> From: owner-rv10-list-server@matronics.com <owner-rv10-list-server@matroni
cs.com> on behalf of Rob Kermanj <flysrv10@gmail.com>
> Sent: Wednesday, November 8, 2017 11:02:27 AM
> To: rv10-list@matronics.com
> Subject: Re: RV10-List: Need latest Navworx UAT Console
>
> Thanks Bob. Yes ...please, please. What do you need from me?
>
> Sent from my iPhone
>
> On Nov 8, 2017, at 8:05 AM, Bob Leffler <bob@thelefflers.com> wrote:
>
>> The avidyne does indeed support adsb+
>>
>> I can assist with writing the AMOC. It will literally take 5-10 minutes t
o create the doc to send to the FAA
>>
>> Email me if you want to go down that path.
>>
>> Get Outlook for iOS
>> From: owner-rv10-list-server@matronics.com <owner-rv10-list-server@matron
ics.com> on behalf of Ralph E. Capen <recapen@earthlink.net>
>> Sent: Wednesday, November 8, 2017 9:31:07 AM
>> To: rv10-list@matronics.com
>> Subject: Re: RV10-List: Need latest Navworx UAT Console
>>
>>
>> Rob,
>>
>> The three AMOCS that have been approved are all for Garmin products.
>> That having been said, the most recent responses from the FAA indicate th
at they may be open to approving other data sources that output the "ADS-B O
UT+" protocol as it contains the necessary data elements required for positi
on reporting. In my updated AMOC, they specifically reference the ADS-B OUT
+ protocol. If the Avidyne outputs it, you should be able to get approval..
.
>>
>> I would suggest putting the AMOC together like we did - we can provide yo
u with what we submitted as a sample if you want...
>>
>> Ralph
>> -----Original Message-----
>>
>> From: Rob Kermanj
>>
>> Sent: Nov 8, 2017 8:52 AM
>>
>> To: rv10-list@matronics.com
>>
>> Subject: Re: RV10-List: Need latest Navworx UAT Console
>>
>>
>>
>> Does anyone know if AMCO applies to Avidyne ID-540?
>> Thanks.
>> On Nov 2, 2017, at 9:38 AM, Bob Leffler <bob@thelefflers.com> wrote:
>> If you need 4.1.0 and the manual, let me know.
>> I haven=99t been able to locate anyone that has 5.0 yet.
>> Get Outlook for iOSFrom: owner-rv10-list-server@matronics.com <owner-rv10
-list-server@matronics.com> on behalf of Bill Watson <Mauledriver@nc.rr.com>
>> Sent: Thursday, November 2, 2017 11:01:53 AM
>> To: rv10-list@matronics.com
>> Subject: RV10-List: Need latest Navworx UAT Console --> RV10-List message
posted by: Bill Watson <Mauledriver@nc.rr.com>
>>
>> I have the Navworx unit that will work with the AMOC given a certified
>> GPS source. But I don't have a copy of the UAT console that will run,
>> looking for help.
>>
>> I tried running the UAT console software I obtained back in 2012 but get
>> an error on loading, "Nonshared DATA segment required", then if fails to
>> open. Anyone have experience with this?
>>
>> A secondary concern I have is that I recall the UAT console loads a
>> version of the Navworx software. If so, this is backlevel for my box
>> (my box had been sent in since then for a maintenance upgrade).
>>
>> Does anyone have a copy of the UAT console that they can share or
>> otherwise advise? Thanks.
>>
>> (I'll be posting on the VAF board as well)
>>
>> Bill "wired up G430w to the deadend box with all appendages crossed" Wats
on
>>
>>
>> ---
>> This email has been checked for viruses by Avast antivirus software.
>> https://www.avast.com/antivirus
>>
>> ==========
>> Email Forum -
>> -List">http://www.matronics.com/Navigator?RV10-List
>> ==========
>> p; - MATRONICS WEB FORUMS -
>> ums.matronics.com
>> ==========
>> p; - NEW MATRONICS LIST WIKI -
>> matronics.com
>> ==========
>> p; - List Contribution Web Site -
>> p; -Matt Dralle, List Admin.
>> http://www.matronics.com/contribution
>> ==========
>>
>>
>>
>> ==========
>> Email Forum -
>> -List">http://www.matronics.com/Navigator?RV10-List
>> ==========
>> p; - MATRONICS WEB FORUMS -
>> ums.matronics.com
>> ==========
>> p; - NEW MATRONICS LIST WIKI -
>> matronics.com
>> ==========
>> p; - List Contribution Web Site -
>> p; -Matt Dralle, List Admin.
>> http://www.matronics.com/contribution
>> ==========
>>
>>
>>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|