---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Wed 01/03/18: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:47 AM - Re: Re: EFIS Configuration (Carlos Trigo) 2. 02:53 PM - Canopy Trimming (David J. Fritzsche) 3. 03:10 PM - Re: Canopy Trimming (Rene) 4. 04:13 PM - Re: Canopy Trimming (Kelly McMullen) 5. 08:24 PM - Re: Canopy Trimming () 6. 09:09 PM - Re: Canopy Trimming (John MacCallum) ________________________________ Message 1 _____________________________________ Time: 02:47:20 AM PST US From: Carlos Trigo Subject: Re: RV10-List: Re: EFIS Configuration Kelly I know that, and I already have done several steps of the configuration, but my idea is to compare data and check if I=99ve done something wrong ( for example I=99m not getting the Nav/Comm radio to comunica-te with t he GDU) or if I should configurate things differently (better). Thanks Carlos Enviado do meu iPhone No dia 03/01/2018, =C3-s 01:57, Kelly McMullen escreve u: > Not to mention that figuring out how to configure the EFIS is one of the m ajor ways to become familiar with the system, > so that by first flight the EFIS isn't one of the new items you are testin g. > > -sent from the I-droid implanted in my forearm > >> On Tue, Jan 2, 2018 at 5:38 PM, nukeflyboy wrote: >> >> This can be tricky and is dependent on a lot of other things, like autopi lot, comms, GPS, ADS-B, and sensors, just to name a few. It is also depende nt on your wiring, since there is some flexibility in where things attach. >> >> Contact me offline at flymoore@charter.net >> >> -------- >> Dave Moore >> RV-6 built and sold >> RV-10 built and flying >> >> >> >> >> Read this topic online here: >> >> http://forums.matronics.com/viewtopic.php?p=477028#477028 >> >> >> >> >> >> >> ========================= >> -List" rel="noreferrer" target="_blank">http://www.matronics.com/Navi gator?RV10-List >> ========================= >> FORUMS - >> eferrer" target="_blank">http://forums.matronics.com >> ========================= >> WIKI - >> errer" target="_blank">http://wiki.matronics.com >> ========================= >> b Site - >> -Matt Dralle, List Admin. >> rel="noreferrer" target="_blank">http://www.matronics.com/contributio n >> ========================= >> >> >> > ________________________________ Message 2 _____________________________________ Time: 02:53:46 PM PST US From: "David J. Fritzsche" Subject: RV10-List: Canopy Trimming What tool are people using to cut the window openings? The curves are too tight for a cutoff wheel and an oscillating tool works great for straight cuts but does not want to cut the curves either. David Fritzsche ________________________________ Message 3 _____________________________________ Time: 03:10:13 PM PST US From: "Rene" Subject: RE: RV10-List: Canopy Trimming I used a combination of the cutoff wheel and small (1") sanding drum on my high speed drill. For smaller holes I used the same types of tools with my Dremel. Rene' 801-721-6080 -----Original Message----- From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of David J. Fritzsche Sent: Wednesday, January 03, 2018 3:53 PM Subject: RV10-List: Canopy Trimming --> What tool are people using to cut the window openings? The curves are too tight for a cutoff wheel and an oscillating tool works great for straight cuts but does not want to cut the curves either. David Fritzsche ________________________________ Message 4 _____________________________________ Time: 04:13:05 PM PST US Subject: Re: RV10-List: Canopy Trimming From: Kelly McMullen Yes, you can get 1 or 2" cut off wheels for the Dremel. The sanding drums are good for the final 1/8-1/16" you need to smooth out. On 1/3/2018 4:09 PM, Rene wrote: > > I used a combination of the cutoff wheel and small (1") sanding drum on my high speed drill. For smaller holes I used the same types of tools with my Dremel. > > Rene' > 801-721-6080 ________________________________ Message 5 _____________________________________ Time: 08:24:00 PM PST US From: Subject: Re: RV10-List: Canopy Trimming The best thing I found was the cutoff wheel, then substituting a jigsaw with a fiberglass cutting blade for the curves. -----Original Message----- From: David J. Fritzsche Sent: Wednesday, January 03, 2018 5:52 PM Subject: RV10-List: Canopy Trimming What tool are people using to cut the window openings? The curves are too tight for a cutoff wheel and an oscillating tool works great for straight cuts but does not want to cut the curves either. David Fritzsche ________________________________ Message 6 _____________________________________ Time: 09:09:03 PM PST US From: John MacCallum Subject: Re: RV10-List: Canopy Trimming I used the half moon vibrating cutter to do most of the cuts. Just the corner of it like a blade. Then I used a power file in the tight radius bends. Cheers John MacCallum RV10 VH DUU > On 4 Jan 2018, at 10:09, Rene wrote: > > > I used a combination of the cutoff wheel and small (1") sanding drum on my high speed drill. For smaller holes I used the same types of tools with my Dremel. > > Rene' > 801-721-6080 > > -----Original Message----- > From: owner-rv10-list-server@matronics.com [mailto:owner-rv10-list-server@matronics.com] On Behalf Of David J. Fritzsche > Sent: Wednesday, January 03, 2018 3:53 PM > To: RV-10 Matronics > Subject: RV10-List: Canopy Trimming > > --> > > What tool are people using to cut the window openings? The curves are too tight for a cutoff wheel and an oscillating tool works great for straight cuts but does not want to cut the curves either. > > David Fritzsche > > > > > > > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.