---------------------------------------------------------- RV10-List Digest Archive --- Total Messages Posted Wed 06/20/18: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 12:54 PM - Spinner Cracks (johngoodman) 2. 02:37 PM - Re: Spinner Cracks (Lew Gallagher) 3. 03:52 PM - Re: Spinner Cracks (johngoodman) 4. 05:31 PM - Re: Re: Spinner Cracks () ________________________________ Message 1 _____________________________________ Time: 12:54:28 PM PST US Subject: RV10-List: Spinner Cracks From: "johngoodman" We are doing our condition inspection and found some very faint cracks around the bolts that pass through the backplate, S 602B. In fact they are so faint, that we had to clean off the primer and do a fingernail test. Anybody else had this? John -------- #40572 Phase One complete in 2011 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=481042#481042 ________________________________ Message 2 _____________________________________ Time: 02:37:06 PM PST US Subject: RV10-List: Re: Spinner Cracks From: "Lew Gallagher" Hey John, Curious, are the cracks in the fiberglass of the spinner or the aluminum backing plate. Pics? - Lew -------- non-pilot crazy about building NOW OFICIALLY BUILDER #40549 Fly off completed ! Read this topic online here: http://forums.matronics.com/viewtopic.php?p=481043#481043 ________________________________ Message 3 _____________________________________ Time: 03:52:49 PM PST US Subject: RV10-List: Re: Spinner Cracks From: "johngoodman" The fiberglass is fine - it's the aluminum backing plate. John -------- #40572 Phase One complete in 2011 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=481046#481046 ________________________________ Message 4 _____________________________________ Time: 05:31:56 PM PST US From: Subject: Re: RV10-List: Re: Spinner Cracks I haven't seen that, but since it's the aluminum, I would suspect vibration/out of balance. Obviously, replace the plate. But before you do, maybe slowly run it up while feeling the dash for vibration? Get someone to electronically balance your prop on the plane to check it out after it's been replaced? We've got a guy in our EAA chapter here in Greenville, SC that gives a group rate for balancing if several want to do it at one sitting. Before mounting the spinner, I put it on a record turntable and it checked out very true. Keep posting your research results. Later, - Lew -----Original Message----- From: johngoodman Sent: Wednesday, June 20, 2018 6:50 PM Subject: RV10-List: Re: Spinner Cracks The fiberglass is fine - it's the aluminum backing plate. John -------- #40572 Phase One complete in 2011 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=481046#481046 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv10-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV10-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv10-list Browse Digests http://www.matronics.com/digest/rv10-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.