Today's Message Index:
----------------------
1. 06:01 AM - Cup holders? (David Carr)
2. 06:26 AM - Re: Cup holders? (Bob Leffler)
3. 08:34 AM - Re: Cup holders? (Dan Masys)
4. 08:51 AM - Re: Cup holders? (Robert Jones)
5. 04:04 PM - Re: Cup holders? (Bob Turner)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Anybody have a slick cup holder setup for the front seat?
I'm currently rocking the stock tunnel with no console.
David
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Cup holders? |
Aerosportproducts.com
Get Outlook for iOS<https://aka.ms/o0ukef>
________________________________
From: owner-rv10-list-server@matronics.com <owner-rv10-list-server@matronic
s.com> on behalf of David Carr <junk@dcarr.org>
Sent: Sunday, May 30, 2021 9:00:00 AM
Subject: RV10-List: Cup holders?
Anybody have a slick cup holder setup for the front seat?
I'm currently rocking the stock tunnel with no console.
David
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Cup holders? |
Not slick but cheap and effective, have used one of these for the past 13
years, velcroed to the center tunnel far forward (just behind velcroed
halon fire extinguisher):
https://www.amazon.com/Hopkins-SMT-Go-Gear-Cupholder/dp/B000FGIBYQ
Pulse oximeter fits in the little compartment between the cup holders.
-Dan Masys
On Sun, May 30, 2021 at 6:31 AM Bob Leffler <bob@thelefflers.com> wrote:
> Aerosportproducts.com
>
> Get Outlook for iOS <https://aka.ms/o0ukef>
> ------------------------------
> *From:* owner-rv10-list-server@matronics.com <
> owner-rv10-list-server@matronics.com> on behalf of David Carr <
> junk@dcarr.org>
> *Sent:* Sunday, May 30, 2021 9:00:00 AM
> *To:* rv10-list@matronics.com <rv10-list@matronics.com>
> *Subject:* RV10-List: Cup holders?
>
> Anybody have a slick cup holder setup for the front seat?
> I'm currently rocking the stock tunnel with no console.
>
> David
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Cup holders? |
I put in a South Florida Sport Aviation armrest with cup holders. It is very
light a screws down with the existing tunnel cover screws. It starts aft of
the fuel selector. I don=99t have a throttle quadrant. My engine cont
rols are hung under a Stein Air instrument panel in a custom made panel. If y
ou have the whole throttle quadrant from SFSA or Aerosports you probably hav
e to stick with their products to make them work together.
https://sfsportaviation.com/index.php?route=product/product&path=62_81_8
3&product_id=59
Robert Jones
> On May 30, 2021, at 6:30 AM, Bob Leffler <bob@thelefflers.com> wrote:
>
> =EF=BB
> Aerosportproducts.com
>
> Get Outlook for iOS
> From: owner-rv10-list-server@matronics.com <owner-rv10-list-server@matroni
cs.com> on behalf of David Carr <junk@dcarr.org>
> Sent: Sunday, May 30, 2021 9:00:00 AM
> To: rv10-list@matronics.com <rv10-list@matronics.com>
> Subject: RV10-List: Cup holders?
>
> Anybody have a slick cup holder setup for the front seat?
> I'm currently rocking the stock tunnel with no console.
>
> David
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Cup holders? |
I built a center arm rest out of some spare foam, covered it with left over cloth
from the interior side walls. Mounted a plastic fold-up cup holder from Amazon
(3 for $10 if I recall) to the forward side of the arm rest. Right size for
a 12 oz soda can; works okay. Truth is, I rarely use it. If I'm taking fluids
along for me, I usually look for a plastic bottle with wide-mouth, screw on
cap, just in case I have to put the fluids back, if you catch my drift...
--------
Bob Turner
RV-10 QB
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=502136#502136
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|