Today's Message Index:
----------------------
 
     1. 05:38 AM - Re: Re: iflyrv10 door pins question (Werner Schneider)
     2. 05:39 AM - Re: Re: iflyrv10 door pins question (Werner Schneider)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
05:38:43 AM PST US
Subject: 
Re: iflyrv10 door pins question
From: 
Werner Schneider <glastar@gmx.net>
      
      
      I have the iFlyRV10 pins not the planearounds :)
      
      On 03.02.2023 00:05, Vol88 wrote:
      >
      > I just tried an AN5 nut on the stud that connects my aluminum tube to my Planearound
      pin. It fit perfectly, with no drag.
      >
      > Perhaps your threads were damaged or contaminated? You could try running a rethreader
      (thread cleaner) to check and straighten the threads. I would start with
      a thread gauge to make sure it's 5/16-24 first.
      >
      >
      > Read this topic online here:
      >
      > http://forums.matronics.com/viewtopic.php?p=510113#510113
      >
      >
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
05:39:38 AM PST US
Subject: 
Re: iflyrv10 door pins question
From: 
Werner Schneider <glastar@gmx.net>
      
      
      Thanks Tim, I have to see where I misplaced my imperial thread guide :)
      
      On 03.02.2023 00:58, Tim Olson wrote:
      >
      > If that doesn't work, I'm guessing it's 5/16-18 if it looks coarse.
      > I can't remember for sure.
      > Tim
      >
      >
      > On 2/2/2023 5:05 PM, Vol88 wrote:
      >>
      >> I just tried an AN5 nut on the stud that connects my aluminum tube to 
      >> my Planearound pin. It fit perfectly, with no drag.
      >>
      >> Perhaps your threads were damaged or contaminated? You could try 
      >> running a rethreader (thread cleaner) to check and straighten the 
      >> threads. I would start with a thread gauge to make sure it's 5/16-24 
      >> first.
      >>
      >>
      >>
      >>
      >> Read this topic online here:
      >>
      >> http://forums.matronics.com/viewtopic.php?p=510113#510113
      >>
      >>
      >>
      >>
      >>
      >>
      >>
      >>
      >>
      >
      >
      
      








Other Matronics Email List Services




Post A New Message
  
rv10-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/RV10-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/rv10-list
Browse RV10-List Digests
  
http://www.matronics.com/digest/rv10-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --