RV3-List Digest Archive

Mon 06/02/03


Total Messages Posted: 1



Today's Message Index:
----------------------
 
     1. 12:38 AM - Re: Re: RV3-List Digest: 2 Msgs - 05/21/03 (Bruce Stewart)
 
 
 


Message 1


  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 12:38:03 AM PST US
    From: "Bruce Stewart" <bruce.stewart1@bigpond.com>
    Subject: Re: RV3-List Digest: 2 Msgs - 05/21/03
    --> RV3-List message posted by: "Bruce Stewart" <bruce.stewart1@bigpond.com> Bob, I found the article I was reading in 21 years of RV loonies and it was based around the RV4 mount angles and if I recall someone had done a few heavy landings and the 50 thou ones were cracked so 63 thou ones were replaced. I gather if the origional ones are looked after there shouldn't be a problem. B > > Bruce, > Don't tell me I've got to remake the engine mount angles in 063 ! - All > those hours mining the ore etc etc. > Both my sets of drawings (printed 1973 and 1984) have .050. Are the new > ready-made ones .063 ? > > Paser did wonders with his M-II, but I think my -3 with an 0-320 and perhaps > PR wheel pants will be 'adequate' esp. in UK, where the distances are short. > Always happy to save fuel money though, so may put some effort into details > to keep drag down. > Thinking about a flat-wrap windscreen, mainly for aesthetics, but may also > spread out and reduce any high-pressure area at the bottom centre of the > standard bubble, at the cost of distortion in the landing flare. Doesn't > obey the KISS principle though. > > Bob > > (Up top and getting, well, a bit less cold!) > > ----- Original Message ----- > > > > Thanks Bob, > > > > I've recently bogged down in thoughts about changing some aspects > > of the RV 3 after reading Kent Pasers book "Speed with Economy" > > which was an eye opener, he attained 60 mph more and 50% reduction > > in fuel on his Mustang II, as for the rudder pedals thats just a bye the > bye > > but important non the less. > > > > I also notice the .050 4130 for the engine mount/ longeron brackets and > > somewhere which I can't recall there was a change to .063 thou, are yours > > the > > .050?? > > > > Bruce > > Down under and getting cold! > >




    Other Matronics Email List Services

  • Post A New Message
  •   rv3-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/RV3-List.htm
  • Full Archive Search Engine
  •   http://www.matronics.com/search
  • 7-Day List Browse
  •   http://www.matronics.com/browse/rv3-list
  • Browse RV3-List Digests
  •   http://www.matronics.com/digest/rv3-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contributions

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --