Today's Message Index:
----------------------
1. 10:28 AM - Error on drawing 16? (RV8PILOTPAUL@aol.com)
2. 12:09 PM - Re: Error on drawing 16? (Randy Lervold)
3. 01:10 PM - Re: Error on drawing 16? (RV8PILOTPAUL@aol.com)
4. 07:12 PM - Re: Error on drawing 16? (Leesafur@aol.com)
5. 10:06 PM - New page on www.LessDrag.com (LessDragProd@aol.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Error on drawing 16? |
--> RV3-List message posted by: RV8PILOTPAUL@aol.com
Is it me or are the hole heights of VS-310 and VS-309 reversed?
Hole height of VS-310 is shown as 1 1/4 and for VS-309 as 1 3/8. Since
VS-309 sits on the 1/8 inch spar doubler, it seems like its hole height should
be
less than the VS-310
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Error on drawing 16? |
--> RV3-List message posted by: "Randy Lervold" <randy@romeolima.com>
You might consider posting this over on the YahooGroups RV-3 list, it's
where the RV-3 community has collected.
http://groups.yahoo.com/group/RV-3/
I'll try to remember to check my plans tonight having just gone through this
stage.
Randy Lervold
www.rv-3.com
----- Original Message -----
From: <RV8PILOTPAUL@aol.com>
Subject: RV3-List: Error on drawing 16?
> --> RV3-List message posted by: RV8PILOTPAUL@aol.com
>
> Is it me or are the hole heights of VS-310 and VS-309 reversed?
>
> Hole height of VS-310 is shown as 1 1/4 and for VS-309 as 1 3/8. Since
> VS-309 sits on the 1/8 inch spar doubler, it seems like its hole height
should be
> less than the VS-310
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Error on drawing 16? |
--> RV3-List message posted by: RV8PILOTPAUL@aol.com
I've never been able to join the Yahoo group; everytime I try I get a message
saying they are unable to process my request at this time
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Error on drawing 16? |
--> RV3-List message posted by: Leesafur@aol.com
In a message dated 10/4/2004 12:28:43 PM Central Standard Time,
RV8PILOTPAUL@aol.com writes:
Is it me or are the hole heights of VS-310 and VS-309 reversed?
Hole height of VS-310 is shown as 1 1/4 and for VS-309 as 1 3/8. Since
VS-309 sits on the 1/8 inch spar doubler, it seems like its hole height
should be
less than the VS-310
Wow that's a good eye. The manual says
"The dimensions given on DWG 16 for the fore and aft spacing between the
hingline and the rear spar have been extensively checked. The hinges differ
because the VS-309 is measured from the VS-307 reinforcement plate, while VS-310
is
measured from the VS-303 spar web."
With that said, sounds like the blueprint is wrong.
I put my rudder and stabilizer together to take a look see and It looks
fine like that. If you end up calling Vans about this let us know what they
say. I'll also post this to the yahoo group to see what the boys over there have
to say.
Lee
Anoka, MN
RV-3 Wing
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | New page on www.LessDrag.com |
rv10-list@matronics.com, RV10@yahoogroups.com
--> RV3-List message posted by: LessDragProd@aol.com
Hi All,
I've added a new page on my website for new and used propellers being
offered for sale.
If you have a propeller you would like to sell; just send me an Email of
what you want listed.
If you are looking for a propeller, you can check the propeller page just
after antenna's under Products. There is already a Hartzell CS propeller for
a
Lycoming 320 and a Lycoming 360 listed.
_www.lessdrag.com_ (http://www.lessdrag.com)
Regards,
Jim Ayers
Less Drag products, Inc.
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|