Today's Message Index:
----------------------
 
     1. 01:01 PM - Hard starting (Phil Smith)
     2. 03:07 PM - Re: Hard starting (Genev E Reed)
     3. 09:26 PM - electric flap motor stops (Doyal R Plute)
 
 
 

Message 1


					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
01:01:21 PM PST US
From: 
"Phil Smith" <phil@analysis-inc.com>
Subject: 
Hard starting
      
      --> RV6-List message posted by: "Phil Smith" <phil@analysis-inc.com>
      
      
      Hi Guys,
      I have an RV-6 with a O-360 and am having trouble with hot (95 degree
      F.) restarts. I have to pump the devil out of it and if I turn on the
      electric fuel pump it just dies. It starts perfectly when cold or cool.
      A friend suggested a shroud around the fuel pump with a piece of scat
      tubing. If that is the answer, is anyone making the shroud?
      Thanks,
      Phil
      
      
      
      
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
03:07:40 PM PST US
Subject: 
Re: Hard starting
From: 
Genev E Reed <genevreed@juno.com>
      
      --> RV6-List message posted by: Genev E Reed <genevreed@juno.com>
      
      Phil: I have the O360 also, On hot restarts I have to start it with
      Throtle off, Mixture off and crank till it fires and then push the
      mixture in. If you knew this just disregard.
        Doyle Reed 7A flying 55 Hs. leaving for OSH Monday morning.
      
      
      
      
      
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
09:26:54 PM PST US
From: 
Doyal R Plute <dplute@sbcglobal.net>
Subject: 
electric flap motor stops
      
      --> RV6-List message posted by: Doyal R Plute <dplute@sbcglobal.net>
      
      I have just installed my flaps with the electric flap motor.  I have set the flap
      up position where the control stops in the up position ok...but going down
      it will go to about 60 degrees before it stops on its own.   How do you adjust
      the travel to stop at 40 degrees?  Did I miss something about adjusting flap
      stops...?  Maybe microswitches are needed?
      
      Any help will be appreciated
      Thanks
      Doyal
      N246dp
      
      
      
      
      
      








Other Matronics Email List Services




Post A New Message
  
rv6-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/RV6-List.htm
Full Archive Search Engine
  
http://www.matronics.com/search
7-Day List Browse
  
http://www.matronics.com/browse/rv6-list
Browse RV6-List Digests
  
http://www.matronics.com/digest/rv6-list
Browse Other Lists
  
http://www.matronics.com/browse
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contributions









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --