Today's Message Index:
----------------------
1. 09:04 AM - Re: canopy half (knepperh)
2. 09:26 PM - Fab Air Box (Mike Comeaux)
3. 10:25 PM - Re: Fab Air Box (Stein Bruch)
Message 1
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV6-List message posted by: "knepperh" <knepperh@ywave.com>
HI BUD, JUST GOT BAACK FROM PACKWOOD, WHERE I WAS REBUILDING A DECK. THEY
HAD A GREAT CAR SHOW THERE THIS WEEKEND. HOPE YOU ALL GOT HOME OK WITH THE
CANOPY. HOW DID IT GO CUTTING THE FRONT HALF OFF? HAVE A GREAT DAY.
HAROLD
----- Original Message -----
From: "Balone Marine" <balone_99@yahoo.com>
Subject: RV6-List: canopy half
> --> RV6-List message posted by: Balone Marine <balone_99@yahoo.com>
>
> looking for the aft or canopy half of the whole canopy
> somebody out there cracked the windshield Excuse me
> windscreen and had to buy a whole new canopy, I need
> the slider part, Will pay shipping and?
> Bud
>
> __________________________________
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV6-List message posted by: "Mike Comeaux" <mcomeaux@bendnet.com>
Any suggestions? After putting all components together
the air box is barely touching the side of the air scoop.
I already have the scoop glassed on & the air box all
riveted togetther. How much does the engine move/vibrate?
Any Recommendations? RV6A---0-360 Fixed
Regards---Mike Comeaux
mcomeaux@bendnet.net
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV6-List message posted by: "Stein Bruch" <stein@steinair.com>
The simple solution is simply to make a new plate for mounting the FAB to
the Carb/Servo and make the center hole "off center"! I ended up making 3
of to get things perfect. Since Lycoming mounts the carbs/servos all over
the place (Rarely in the center of the sump) this happens. My Fuel
Injection Servo sits about 1.5" off of center, hence my requirement for a
new plate that offsets the FAB to line up with the cowl inlet, Otherwise my
FAB was hitting the side of the scoop also.
Hope this helps!
Cheers,
Stein Bruch,
RV6, AEIO-360/Fixed.
-----Original Message-----
From: owner-rv6-list-server@matronics.com
[mailto:owner-rv6-list-server@matronics.com]On Behalf Of Mike Comeaux
Subject: RV6-List: Fab Air Box
--> RV6-List message posted by: "Mike Comeaux" <mcomeaux@bendnet.com>
Any suggestions? After putting all components together
the air box is barely touching the side of the air scoop.
I already have the scoop glassed on & the air box all
riveted togetther. How much does the engine move/vibrate?
Any Recommendations? RV6A---0-360 Fixed
Regards---Mike Comeaux
mcomeaux@bendnet.net
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|