RV6-List Digest Wed 07/30/03

RV6-List Digest Archive

Wed 07/30/03

Total Messages Posted: 2



Today's Message Index:
----------------------
 
     1. 03:45 AM - RV6 vertical stabiliser (Shirley Harding)
     2. 04:35 AM - Re: RV6 vertical stabiliser (Jerry Calvert)
 
 
 

Message 1


					NEXT  Skip to NEXT Message
	LIST  Reply to LIST Regarding this Message
		SENDER  Reply to SENDER Regarding this Message

      
      
Time: 03:45:04 AM PST US
From: "Shirley Harding" <shirleyh@starwon.com.au>
Subject: RV6 vertical stabiliser      
      --> RV6-List message posted by: "Shirley Harding" <shirleyh@starwon.com.au>
      
      Hi all,
      
      having a problem putting my VS onto my quickbuild fuse.
      
      The 2 anglebar longerons  run right to the end of the tail fuse skin and then another
      half inch beyond that.
      
      My VS rear spar wont fit in unless these are removed in some part.
      
      Also there are no instructions on fitting the part F-612B angle/control stop to
      this area and it seems the VS bolts onto it   (and why does it need that little
      tongue cut out of it) ?
      
      Anybody any ideas?
      
      
      Shirley
      
      
      
      
      
      

Message 2


					INDEX  Back to Main INDEX
				PREVIOUS  Skip to PREVIOUS Message
					NEXT  Skip to NEXT Message
	LIST  Reply to LIST Regarding this Message
		SENDER  Reply to SENDER Regarding this Message

      
      
Time: 04:35:40 AM PST US
From: "Jerry Calvert" <rv6@cox.net>
Subject: Re: RV6 vertical stabiliser      
      --> RV6-List message posted by: "Jerry Calvert" <rv6@cox.net>
      
      The longeron protrusion will need to be trimmed to allow the vertical stab
      spar to fit.
      
      Good day,
      Jerry Calvert
      Edmond ok
      RV6 N296JC res
      ----- Original Message -----
      From: "Shirley Harding" <shirleyh@starwon.com.au>
      Subject: RV6-List: RV6 vertical stabiliser
      
      
      > --> RV6-List message posted by: "Shirley Harding"
      <shirleyh@starwon.com.au>
      >
      > Hi all,
      >
      > having a problem putting my VS onto my quickbuild fuse.
      >
      > The 2 anglebar longerons  run right to the end of the tail fuse skin and
      then another half inch beyond that.
      >
      > My VS rear spar wont fit in unless these are removed in some part.
      >
      > Also there are no instructions on fitting the part F-612B angle/control
      stop to this area and it seems the VS bolts onto it   (and why does it need
      that little tongue cut out of it) ?
      >
      > Anybody any ideas?
      >
      >
      > Shirley
      >
      >
      
      
      
      
      
      








Other Matronics Email List Services




Post A New Message    rv6-list@matronics.com
UN/SUBSCRIBE    http://www.matronics.com/subscription
List FAQ    http://www.matronics.com/FAQ/RV6-List.htm
Full Archive Search Engine    http://www.matronics.com/search
7-Day List Browse    http://www.matronics.com/browse/rv6-list
Browse RV6-List Digests    http://www.matronics.com/digest/rv6-list
Browse Other Lists    http://www.matronics.com/browse
Archive Downloading    http://www.matronics.com/archives
Photo Share    http://www.matronics.com/photoshare
Other Email Lists    http://www.matronics.com/emaillists
Contributions    http://www.matronics.com/contributions









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --