Today's Message Index:
----------------------
1. 07:11 AM - Re: Nippondenso (Larry Rush)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Thanks George............
"LIMA TANGO SENDS"
----- Original Message ----
From: George Frost <ghfrost@earthlink.net>
Sent: Thursday, June 15, 2006 2:59:25 PM
Subject: Re: RV6-List: Nippondenso
My regulator on my Nippondenso is NAPA UR572SB. There are three pins.
Two are parallel and vertical, one is perpendicular and horizontal. The
perpendicular pin is above the parallel pins. It is the sense pin.
With the sense pin located above the parallel pins, the left pin is the
field pin and the right pin is for the automatic choke according to
NAPA dealer info. We, of course have no automatic choke so it is not
used. Left pin field wire from bus, top pin sense wire to output post.
It works that way.
On Jun 14, 2006, at 10:43 AM, Larry Rush wrote:
> I believe (from memory) there are two pins on the plug and one output
> terminal, so which one is the sense wire? One pin is the field, one is
> the fault light, and....? It has been a while since I wired mine.
> May have "faulty" memory.....<:
> Larry, RV-6A
>
> "LIMA TANGO SENDS"
>
>
> ----- Original Message ----
> From: CustomACProp@aol.com
> To: rv6-list@matronics.com
> Sent: Wednesday, June 7, 2006 12:42:23 AM
> Subject: Re: RV6-List: Nippondenso
>
>
> Hi George,
>
> It worked for me. I had the same symptom and found I didn't have the
> sense wire installed.
> 14.9 went to 14.2 volts.
>
> Thanks,
> Jim Ayers
> RV-6A 54 hrs TT 19 hours remaining on 25 hour Phase 1. Don't ask.
>
> In a message dated 06/05/2006 11:59:11 PM Pacific Daylight Time,
> rv6-list@matronics.com writes:
>> Time: 07:08:36 AM PST US
>> From: George Frost <ghfrost@earthlink.net>
>> Subject: RV6-List: Nippondenso
>>
>> --> RV6-List message posted by: George Frost <ghfrost@earthlink.net>
>>
>> Hi,
>>
>> My Nippondenso altrnator was charging at 14.9 max. I was unable to get
>> info from Duralast ( the rebuilder), Toyata dealers, Matronics RV
>> site,
>> and some A&Ps re: the proper wiring. I had a wire to the field post
>> but
>> none to the sense post. With the help of my son, and a NAPA dealer,
>> the
>> sense wire now goes to the output post and Voila! max charge is 14.2.
>>
>> I thought this might help someone else.
>>
>> George
>
>
My regulator on my Nippondenso is NAPA UR572SB. There are three pins.
Two are parallel and vertical, one is perpendicular and horizontal.
The perpendicular pin is above the parallel pins. It is the sense
pin. With the sense pin located above the parallel pins, the left pin
is the field pin and the right pin is for the automatic choke
according to NAPA dealer info. We, of course have no automatic choke
so it is not used. Left pin field wire from bus, top pin sense wire to
output post. It works that way.
On Jun 14, 2006, at 10:43 AM, Larry Rush wrote:
<excerpt><fontfamily><param>Times New Roman</param><bigger><bigger>I
believe (from memory) there are two pins on the plug and one output
terminal, so which one is the sense wire? One pin is the field, one is
the fault light, and....? It has been a while since I wired mine.
May have "faulty" memory.....<<:</bigger></bigger></fontfamily>
<fontfamily><param>Times New Roman</param><bigger><bigger>Larry, RV-6A</bigger></bigger></fontfamily>
<fontfamily><param>Times New Roman</param><bigger><bigger> </bigger></bigger></fontfamily>
<fontfamily><param>Times New Roman</param><bigger><bigger>"LIMA TANGO
SENDS"</bigger></bigger></fontfamily>
<fontfamily><param>Times New Roman</param><bigger><bigger>-----
Original Message ----</bigger></bigger></fontfamily>
<fontfamily><param>Times New Roman</param><bigger><bigger>From:
CustomACProp@aol.com</bigger></bigger></fontfamily>
<fontfamily><param>Times New Roman</param><bigger><bigger>To:
rv6-list@matronics.com</bigger></bigger></fontfamily>
<fontfamily><param>Times New Roman</param><bigger><bigger>Sent:
Wednesday, June 7, 2006 12:42:23 AM</bigger></bigger></fontfamily>
<fontfamily><param>Times New Roman</param><bigger><bigger>Subject: Re:
RV6-List: Nippondenso</bigger></bigger></fontfamily>
<fontfamily><param>Arial</param><smaller>Hi George,</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller> </smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>It worked for me. I had the
same symptom and found I didn't have the sense wire installed.</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>14.9 went to 14.2 volts.</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller> </smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>Thanks,</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>Jim Ayers</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>RV-6A 54 hrs TT 19 hours
remaining on 25 hour Phase 1. Don't ask.</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller> </smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>In a message dated 06/05/2006
11:59:11 PM Pacific Daylight Time, rv6-list@matronics.com writes:</smaller></fontfamily>
<excerpt><fontfamily><param>Arial</param><smaller>Time: 07:08:36 AM
PST US</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>From: George Frost
<<ghfrost@earthlink.net></smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>Subject: RV6-List: Nippondenso</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>--> RV6-List message posted
by: George Frost <<ghfrost@earthlink.net></smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>Hi,</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>My Nippondenso altrnator was
charging at 14.9 max. I was unable to get</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>info from Duralast ( the
rebuilder), Toyata dealers, Matronics RV site,</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>and some A&Ps re: the proper
wiring. I had a wire to the field post but</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>none to the sense post. With
the help of my son, and a NAPA dealer, the</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>sense wire now goes to the
output post and Voila! max charge is 14.2.</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>I thought this might help
someone else.</smaller></fontfamily>
<fontfamily><param>Arial</param><smaller>George</smaller></fontfamily>
</excerpt><fontfamily><param>Arial</param><smaller> </smaller></fontfamily>
</excerpt>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|