Today's Message Index:
----------------------
1. 07:26 AM - Looking for Frank Justice manual section (wild1ranch@wild1ranch.com)
2. 09:07 AM - Re: Looking for Frank Justice manual section (Schroeder, Bob (Parts Clerk))
3. 09:14 AM - Re: Looking for Frank Justice manual section (S Hamer)
4. 09:35 AM - (Steve Wieland)
5. 09:47 AM - Re: (BPA)
6. 10:10 AM - Re: (MnwPeeps@AOL.COM)
7. 11:10 AM - Conical engine mount (George Frost)
8. 09:34 PM - Re: (Henry)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Looking for Frank Justice manual section |
Im looking for the section "remove from the jig" all the links I find
seem to be broken.
thanks for your help
Bill
Slow build RV6
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Looking for Frank Justice manual section |
The printed text?
-----Original Message-----
From: owner-rv6-list-server@matronics.com
[mailto:owner-rv6-list-server@matronics.com] On Behalf Of
wild1ranch@wild1ranch.com
Sent: Wednesday, April 30, 2008 8:23 AM
Subject: RV6-List: Looking for Frank Justice manual section
Im looking for the section "remove from the jig" all the links I find
seem to be broken.
thanks for your help
Bill
Slow build RV6
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Looking for Frank Justice manual section |
Bill,
It's a very short section. Here's what it says:
Removing the Fuselage from the Jig
Decide how you are going to support the fuselage once you take it out of the
jig. One really handy way is to make bolt-on front legs. Make a couple of
wood strips about 7 1/2" wide and 24" long, then drill them to bolt where
the main spar goes but extending out about 8" outside the skin. Nail 29"
legs to these and you will have your main longeron 45" off the floor when
you turn the fuselage over. Make a skinny sawhorse for the rear. If you
made the imitation wing for mounting -6A gear legs you can cut them down for
this. These legs make it extremely unlikely that you knock the fuselage
over accidentally.
Remove all the clamps and bolts holding the fuselage in, lift it off, and
set it upright.
End
The next section is "Assorted Small Steps".
I hope this helps.
Steve Hamer
RV-6 flying
Apple Valley, Ca
----- Original Message -----
From: <wild1ranch@wild1ranch.com>
Sent: Wednesday, April 30, 2008 7:23 AM
Subject: RV6-List: Looking for Frank Justice manual section
>
> Im looking for the section "remove from the jig" all the links I find
> seem to be broken.
>
> thanks for your help
>
> Bill
> Slow build RV6
>
>
>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Hi Folks.....I'm interested in an RV6-A in Seattle WA..... is there
anyone that can help me with a look at it before purchase.....I'm a
non-mechanic ex-airline/ ex-fighter guy in NC...thanks!!
Steve
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Steve,
Not sure if they have the time, but contact Butch or Brian at
Showplanes. They are in Medford Oregon. They might be able to help or
direct you to someone who can.
Allen Barrett
BPE, Inc.
-----Original Message-----
From: owner-rv6-list-server@matronics.com
[mailto:owner-rv6-list-server@matronics.com] On Behalf Of Steve Wieland
Sent: Wednesday, April 30, 2008 10:30 AM
Subject: RV6-List:
Hi Folks.....I'm interested in an RV6-A in Seattle WA..... is there
anyone that can help me with a look at it before purchase.....I'm a
non-mechanic ex-airline/ ex-fighter guy in NC...thanks!!
Steve
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Steve - If that one doesn't look so good, or doesn't work out, you
might give me a yell.
I have a 6-A that is casually for sale - Boston area. New Engine, prop.
I'm also ex-mil and ret. airline.
_flmr123@aol.com_ (mailto:flmr123@aol.com)
**************Need a new ride? Check out the largest site for U.S. used car
listings at AOL Autos.
(http://autos.aol.com/used?NCID=aolcmp00300000002851)
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Conical engine mount |
I might as well try this again. I have a Lycoming conical engine mount
and gear legs for an RV_6. Anyone using an early 0-320?
Message 8
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: e: RV6-List: |
Hello Steve:
I'm based in Seattle. If you tell me where the plane is, exactly what
you want me to look at (a checklist would be perfect) and let the seller
know my email address, I can go look at it for you, fly it if need be,
and send digital pix if you don't already have them from the seller.
Henry Hochberg
RV6 KAWO N72224
Mooney 252 KPAE N252MK
Steve Wieland wrote:
> Hi Folks.....I'm interested in an RV6-A in Seattle WA..... is there
> anyone that can help me with a look at it before purchase.....I'm a
> non-mechanic ex-airline/ ex-fighter guy in NC...thanks!!
> Steve
> *
>
>
> *
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|