RV6-List Digest Sat 10/18/08

RV6-List Digest Archive

Sat 10/18/08

Total Messages Posted: 2



Today's Message Index:
----------------------
 
     1. 12:32 PM - Installing the Vertical Fin on a RV-6AQ (Colleen and Brett Herrick)
     2. 01:05 PM - Re: Installing the Vertical Fin on a RV-6AQ (Patrick Kelley)
 
 
 

Message 1


					INDEX  Back to Main INDEX
					NEXT  Skip to NEXT Message
	LIST  Reply to LIST Regarding this Message
		SENDER  Reply to SENDER Regarding this Message

      
      
Time: 12:32:32 PM PST US
From: "Colleen and Brett Herrick" <colleenandbrett@comcast.net>
Subject: Installing the Vertical Fin on a RV-6AQ      
      After installing the vertical fin on my RV-6AQ I find that the rear edge 
      of the vertical fin is 3/16 - 1/4 inch forward of the rear edge of 
      fuselage skins.  I assuming that rear edge of the fuselage skins is to 
      be trimmed to match that of vertical fin.  
      
      Is this correct?  I have not found anything in the plans or instructions 
      that addresses this.
      
      Thanks.
      
      Brett Herrick
      Columbus, IN
      

Message 2


					INDEX  Back to Main INDEX
				PREVIOUS  Skip to PREVIOUS Message
					NEXT  Skip to NEXT Message
	LIST  Reply to LIST Regarding this Message
		SENDER  Reply to SENDER Regarding this Message

      
      
Time: 01:05:57 PM PST US
From: "Patrick Kelley" <webmaster@flion.com>
Subject: Installing the Vertical Fin on a RV-6AQ      
      If your rear spar lines up with the rear bulkhead (it must, or how did you
      mount it?) then everything is fine.  Trim the trailing edges to match.  I
      waited until I fit the empennage fairing and then trimmed everything at
      once.
      
      
      Patrick Kelley - RV-6A - 1st Engine start today!!
      
      
      From: owner-rv6-list-server@matronics.com
      [mailto:owner-rv6-list-server@matronics.com] On Behalf Of Colleen and Brett
      Herrick
      Sent: Saturday, October 18, 2008 12:32 PM
      Subject: RV6-List: Installing the Vertical Fin on a RV-6AQ
      
      
      After installing the vertical fin on my RV-6AQ I find that the rear edge of
      the vertical fin is 3/16 - 1/4 inch forward of the rear edge of fuselage
      skins.  I assuming that rear edge of the fuselage skins is to be trimmed to
      match that of vertical fin.  
      
      
      Is this correct?  I have not found anything in the plans or instructions
      that addresses this.
      
      
      Thanks.
      
      
      Brett Herrick
      
      Columbus, IN
      
      








Other Matronics Email List Services




Post A New Message    rv6-list@matronics.com
UN/SUBSCRIBE    http://www.matronics.com/subscription
List FAQ    http://www.matronics.com/FAQ/RV6-List.htm
Web Forum Interface To Lists    http://forums.matronics.com
Matronics List Wiki    http://wiki.matronics.com
7-Day List Browse    http://www.matronics.com/browse/rv6-list
Browse RV6-List Digests    http://www.matronics.com/digest/rv6-list
Browse Other Lists    http://www.matronics.com/browse
Live Online Chat!    http://www.matronics.com/chat
Archive Downloading    http://www.matronics.com/archives
Photo Share    http://www.matronics.com/photoshare
Other Email Lists    http://www.matronics.com/emaillists
Contributions    http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --