---------------------------------------------------------- RV6-List Digest Archive --- Total Messages Posted Thu 03/26/09: 2 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 06:14 AM - Re: Filler for "Unwanted" Rivet Holes ??? (Smcm75@aol.com) 2. 02:39 PM - Re: Filler for "Unwanted" Rivet Holes ??? (J. Brunke) ________________________________ Message 1 _____________________________________ Time: 06:14:23 AM PST US From: Smcm75@aol.com Subject: Re: RV6-List: Filler for "Unwanted" Rivet Holes ??? In a message dated 3/26/2009 1:04:26 AM Eastern Daylight Time, gareywittich2000@yahoo.com writes: What material have you Builders used to fill in a couple of unwanted holes in the Skin, where a rivet can NOT be placed to plug the hole ???? Is Super-Fil a possible solution ???? Nope try cutting a little circular patch from .016 aluminum about 3/4" dia. mix up a small batch of b-2 compound and stick the patch on the hole from the rear. Then clean the b-2 out of the hole if it oozes in with MEK. After the b-2 is set up you can fill the hole with featherfill and it will never vibrate out. **************Feeling the pinch at the grocery store? Make dinner for $10 or less. (http://food.aol.com/frugal-feasts?ncid=emlcntusfood00000001) ________________________________ Message 2 _____________________________________ Time: 02:39:42 PM PST US From: "J. Brunke" Subject: Re: RV6-List: Filler for "Unwanted" Rivet Holes ??? Ok you got a new one on me. I tried looking up B-2 compound and couldn't find anything on it. Is this stuff like JB weld? John ----- Original Message ----- From: Smcm75@aol.com To: rv6-list@matronics.com Sent: Thursday, March 26, 2009 7:13 AM Subject: Re: RV6-List: Filler for "Unwanted" Rivet Holes ??? In a message dated 3/26/2009 1:04:26 AM Eastern Daylight Time, gareywittich2000@yahoo.com writes: What material have you Builders used to fill in a couple of unwanted holes in the Skin, where a rivet can NOT be placed to plug the hole ???? Is Super-Fil a possible solution ???? Nope try cutting a little circular patch from .016 aluminum about 3/4" dia. mix up a small batch of b-2 compound and stick the patch on the hole from the rear. Then clean the b-2 out of the hole if it oozes in with MEK. After the b-2 is set up you can fill the hole with featherfill and it will never vibrate out. ------------------------------------------------------------------------- ----- Feeling the pinch at the grocery store? Make dinner for $10 or less. ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv6-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV6-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv6-list Browse Digests http://www.matronics.com/digest/rv6-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.