Today's Message Index:
----------------------
1. 12:17 PM - Filler for unwanted Rivet Holes (gareywittich2000@yahoo.com)
2. 06:25 PM - on Ailerons (maurice murillo)
3. 09:23 PM - Re: on Ailerons (Charles Ennis)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Filler for unwanted Rivet Holes |
Greetings:
What material have you Builders used to fill in a couple of unwanted holes
in the Skin, where a rivet can NOT be placed to plug the hole ????
Is Super-Fil a possible solution ????
Thanks,---Garey Wittich- Santa Monica, CA
=0A=0A=0A
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Hi:
My RV6a is now painted=2C the elevators had to be re balance=2C now I am a
ligning the Ailerons.
Iadjusted the rods=2C so that both ailerons are perfectly aligned with Flap
s/and Wing tips. stick=2C Vertical
and center. Al this was done...there is no play that I can feel or hear...
So=2C on the ground everything is well....but=2C when flying=2C I notice
=2C ailerons are not aligned=2C when
flying straight and level..there is a difference of about 1/4'=2C on each s
ide...
I cannot understand... I called Van's they did not understand my question
=2C or do not know what to do..
Any suggestions=2C ideas? Everything was perfect before paint...
Again=2C everything looks and feels=2C aligned...on the ground..
thanks for comments
maurice
rv6a
do not archive
_________________________________________________________________
Windows Live=99 SkyDrive=99: Get 25 GB of free online storage.
http://windowslive.com/online/skydrive?ocid=TXT_TAGLM_WL_SD_25GB_062009
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Maurice,
If the misalignment is with the flaps..it's not unusual for the flaps
to position slightly higher in flight then on the ground, due to lifting
loads. Having said that, as long as the flaps/wings are symmetrical
during flight I wouldn't worry about a slight misalignment. But that's
me, I gave up on perfection while building my 6A and decided to settle
for the best I could do. As an aside, lifting loads will also remove all
the slack from the ailerons and possibly cause a slight misalignment
with the wing tip trailing edge.
I hope this helps.
Charlie Ennis
----- Original Message -----
From: maurice murillo
To: rv6-list@matronics.com
Sent: Monday, June 08, 2009 9:24 PM
Subject: RV6-List: on Ailerons
Hi:
My RV6a is now painted, the elevators had to be re balance, now I am
aligning the Ailerons.
Iadjusted the rods, so that both ailerons are perfectly aligned with
Flaps/and Wing tips. stick, Vertical
and center. Al this was done...there is no play that I can feel or
hear...
So, on the ground everything is well....but, when flying, I notice,
ailerons are not aligned, when
flying straight and level..there is a difference of about 1/4', on
each side...
I cannot understand... I called Van's they did not understand my
question, or do not know what to do..
Any suggestions, ideas? Everything was perfect before paint...
Again, everything looks and feels, aligned...on the ground..
thanks for comments
maurice
rv6a
do not archive
-------------------------------------------------------------------------
-----
Windows Live=99 SkyDrive=99: Get 25 GB of free online storage. Get it
on your BlackBerry or iPhone.
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|