---------------------------------------------------------- RV6-List Digest Archive --- Total Messages Posted Thu 10/30/14: 2 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:25 PM - Re: Re: RV6-List Digest: 0 Msgs - 10/27/14 (Ed Hollestelle) 2. 03:14 PM - Re: Re: RV6-List Digest: 0 Msgs - 10/27/14 (Warren) ________________________________ Message 1 _____________________________________ Time: 02:25:20 PM PST US From: "Ed Hollestelle" Subject: RE: RV6-List: RE: RV6-List Digest: 0 Msgs - 10/27/14 Warren, Thanks for your input. I understand the need for a good seal (and fit) so that is what made me think thatif I put the bottom seal on the cowling side, it will fit without pushing it over the edge. If I use a small strip of alluminum (as with the front of the bottom baffle inlet) to attach the fabric seal and have that about 1" over the top on both sides it should work. The horizontal top seal will then fit tightly in between. I am just thinking that it will be easier to install the cowling that way. What do you think? Thanks again-Ed. -----Original Message----- From: owner-rv6-list-server@matronics.com [mailto:owner-rv6-list-server@matronics.com] On Behalf Of Warren Brecheisen Sent: Wednesday, October 29, 2014 2:49 PM Subject: RE: RV6-List: RE: RV6-List Digest: 0 Msgs - 10/27/14 Ed, I put my seals on per the plans (RV-6) and it works ok as long as there is enough gap between the end of the inlet on the cowl and the front edge of the FAB. I always have to push the bottom part down around the lip of the inlet when I install the lower cowl. I think your suggestion might work pretty well and, from my experience, it probably would make the lower cowl easier to install. You just need to ensure that you get a pretty good seal all the way around the lip on the cowling. Warren -----Original Message----- From: owner-rv6-list-server@matronics.com [mailto:owner-rv6-list-server@matronics.com] On Behalf Of Ed Hollestelle Sent: Wednesday, October 29, 2014 12:05 PM Subject: RV6-List: RE: RV6-List Digest: 0 Msgs - 10/27/14 I have just completed the FAB on my RV-6 and instructions say to put the seal on the front of the inlet on the FAB side. With the way the cowling goes on (from the bottom) would it not make more sense to attach the bottom of the seal to the inlet on the cowling and the top of the seal on the FAB? Any reason this could not be done or am I overlooking something? Ed Hollestelle. -----Original Message----- From: owner-rv6-list-server@matronics.com [mailto:owner-rv6-list-server@matronics.com] On Behalf Of RV6-List Digest Server Sent: October-28-14 3:03 AM Subject: RV6-List Digest: 0 Msgs - 10/27/14 * ================================================= Online Versions of Today's List Digest Archive ================================================= Today's complete RV6-List Digest can also be found in either of the two Web Links listed below. The .html file includes the Digest formatted in HTML for viewing with a web browser and features Hyperlinked Indexes and Message Navigation. The .txt file includes the plain ASCII version of the RV6-List Digest and can be viewed with a generic text editor such as Notepad or with a web browser. HTML Version: http://www.matronics.com/digest/digestview.php?Style=82701&View=html&Chapter 14-10-27&Archive=RV6 Text Version: http://www.matronics.com/digest/digestview.php?Style=82701&View=txt&Chapter 2014-10-27&Archive=RV6 =============================================== EMail Version of Today's List Digest Archive =============================================== ---------------------------------------------------------- RV6-List Digest Archive --- Total Messages Posted Mon 10/27/14: 0 ---------------------------------------------------------- Today's Message Index: ---------------------- ----- No virus found in this message. Checked by AVG - www.avg.com ----- No virus found in this message. Checked by AVG - www.avg.com ________________________________ Message 2 _____________________________________ Time: 03:14:48 PM PST US Subject: Re: RV6-List: RE: RV6-List Digest: 0 Msgs - 10/27/14 From: Warren I'm sure it would be easier to install the cowling. I dread having to pull off and install the lower cowling. If you are successful with your idea, I would like to see some pictures as I might modify mine. Warren > On Oct 30, 2014, at 4:24 PM, Ed Hollestelle wrote: > > > Warren, > Thanks for your input. > I understand the need for a good seal (and fit) so that is what made me > think thatif I put the bottom seal on the cowling side, it will fit without > pushing it over the edge. > If I use a small strip of alluminum (as with the front of the bottom baffle > inlet) to attach the fabric seal and have that about 1" over the top on both > sides it should work. > The horizontal top seal will then fit tightly in between. > I am just thinking that it will be easier to install the cowling that way. > What do you think? > Thanks again-Ed. > > -----Original Message----- > From: owner-rv6-list-server@matronics.com > [mailto:owner-rv6-list-server@matronics.com] On Behalf Of Warren Brecheisen > Sent: Wednesday, October 29, 2014 2:49 PM > To: rv6-list@matronics.com > Subject: RE: RV6-List: RE: RV6-List Digest: 0 Msgs - 10/27/14 > > > Ed, > > I put my seals on per the plans (RV-6) and it works ok as long as there is > enough gap between the end of the inlet on the cowl and the front edge of > the FAB. I always have to push the bottom part down around the lip of the > inlet when I install the lower cowl. I think your suggestion might work > pretty well and, from my experience, it probably would make the lower cowl > easier to install. You just need to ensure that you get a pretty good seal > all the way around the lip on the cowling. > > Warren > > -----Original Message----- > From: owner-rv6-list-server@matronics.com > [mailto:owner-rv6-list-server@matronics.com] On Behalf Of Ed Hollestelle > Sent: Wednesday, October 29, 2014 12:05 PM > To: rv6-list@matronics.com > Subject: RV6-List: RE: RV6-List Digest: 0 Msgs - 10/27/14 > > > I have just completed the FAB on my RV-6 and instructions say to put the > seal on the front of the inlet on the FAB side. > With the way the cowling goes on (from the bottom) would it not make more > sense to attach the bottom of the seal to the inlet on the cowling and the > top of the seal on the FAB? > Any reason this could not be done or am I overlooking something? > Ed Hollestelle. > > -----Original Message----- > From: owner-rv6-list-server@matronics.com > [mailto:owner-rv6-list-server@matronics.com] On Behalf Of RV6-List Digest > Server > Sent: October-28-14 3:03 AM > To: RV6-List Digest List > Subject: RV6-List Digest: 0 Msgs - 10/27/14 > > * > > ================================================= > Online Versions of Today's List Digest Archive > ================================================= > > Today's complete RV6-List Digest can also be found in either of the two Web > Links listed below. The .html file includes the Digest formatted in HTML > for viewing with a web browser and features Hyperlinked Indexes and Message > Navigation. The .txt file includes the plain ASCII version of the RV6-List > Digest and can be viewed with a generic text editor such as Notepad or with > a web browser. > > HTML Version: > > > http://www.matronics.com/digest/digestview.php?Style=82701&View=html&Chapter > 14-10-27&Archive=RV6 > > Text Version: > > > http://www.matronics.com/digest/digestview.php?Style=82701&View=txt&Chapter > 2014-10-27&Archive=RV6 > > > =============================================== > EMail Version of Today's List Digest Archive > =============================================== > > > ---------------------------------------------------------- > RV6-List Digest Archive > --- > Total Messages Posted Mon 10/27/14: 0 > ---------------------------------------------------------- > > > Today's Message Index: > ---------------------- > > > > > > > > > > > > ----- > No virus found in this message. > Checked by AVG - www.avg.com > > > > > > > > > > > ----- > No virus found in this message. > Checked by AVG - www.avg.com > > > > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message rv6-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/RV6-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/rv6-list Browse Digests http://www.matronics.com/digest/rv6-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.