Today's Message Index:
----------------------
1. 07:15 PM - Fw: RV8-List: R-710 Hole Edge Distance (Charles Becker)
2. 07:29 PM - A GUIDE TO AIRCRAFT PAINTING & CORROSION CONTROL (Garey Wittich)
3. 07:41 PM - Re: Fw: RV8-List: R-710 Hole Edge Distance (Radomir Zaric)
Message 1
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Fw: RV8-List: R-710 Hole Edge Distance |
--> RV7-List message posted by: "Charles Becker" <ctbecker@charter.net>
----- Original Message -----
From: "Charles Becker" <ctbecker@charter.net>
Subject: RV8-List: R-710 Hole Edge Distance
> --> RV8-List message posted by: "Charles Becker" <ctbecker@charter.net>
>
> When I trimmed my R-710 - Rudder Horn Brace - then match drilled the holes
through the skin (4 on each side), the edge distance to the holes came out
at 1/8 inch. It looks a little close to the edge. Do you think I need to
reorder the part?
>
> Charles Becker
> N474CB - RV8A
> Empennage
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | A GUIDE TO AIRCRAFT PAINTING & CORROSION CONTROL |
rv8-list@matronics.com,
"rv9-list@matronics.com
BAYES_60 (1.1 points) BODY": Bayesian.classifier.says.spam.probability.is.60.to.70@[score:0.6584]SUSPICIOUS_RECIPS.Similar.addresses.in.recipient.list
(1.9 points)
--> RV7-List message posted by: Garey Wittich <gareywittich2000@yahoo.com>
SAVE YOURSELF hundreds of hours of research time and
building time, by ordering the comprehensive
"Guide to Painting & Corrosion Control of Aluminum and
Composite Aircraft"
This book took over 600+ hours of research time, by a
fussy Builder. Contains 64 pages of the latest,
practical information - summarized and gathered from
MIL Standards, Paint Shops, Builders like you (what
worked or didn't), Airframe Mfgs, etc. Covers
Products (characteristics & application of) from PP&G,
Dupont, Sherwin W'ms, Sterling, Poly Fiber, Deft,
Randolph Paints, PRC De Soto, US Paints, Aircraft
Finishing Systems, Tempo, 3M, etc.
Some of the Topics covered in the 30 Sections are:
* Aircraft Paints vs Auto Paints and Other
Considerations
* Corrosion Control
* Spray Guns - selecting, adjusting, using
and painting problems
* Brushes / Rollers used with Primers &
Paints
* Prep Methods for Painting - Fiberglass,
Steel and Aluminum
* Epoxy Primers for Aluminum - MIL &
Commercial, Solvent & Water Reducible
* Primers for Fiberglass & Steel
* Wash Primers & Self Etching Primers
* Other Primers - Zinc Chromate,Zinc Oxide,
Enamel
* Paint Types: MIL & Non MIL Polyurethanes
Enamel Types
Acrylics - Lacquers & Enamels
* Acid Etch / Conversion Coatings (Alodine)
* Criteria for selecting a Paint Shop
* 3M Cleaning Pads, Liquid Cleaners and their
effectiveness
* Paint Booths and their Construction
* References - MIL Standards & Tech Orders
* Directory of Aircraft Paint Mfgs, Distrib-
utors, etc. E-Mail addresses, Phone
Numbers, Application Notes
YOUR AIRPLANE is judged by it's Paint Job and it is
costly too, so have the latest "Information" in order
to make good decisions. Contains plenty of "Do's" and
"Don'ts" that save Time, Money and Frustration. Order
today.
Send a check for $25 to (includes Postage within the
US) to:
Garey Wittich
58 Village Parkway
Santa Monica, CA. 90405
__________________________________
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Fw: RV8-List: R-710 Hole Edge Distance |
--> RV7-List message posted by: "Radomir Zaric" <radomirz@vitez.net>
Charles,
You are measuring from the center of the hole, right? Just checked
mine.. right around 1/4" edge distance (from the center). If you had it
clecoed together properly.. it'd be hard to drill it incorrectly.
HTH>
Radomir
RV-7A Emp.
-----Original Message-----
From: owner-rv7-list-server@matronics.com
[mailto:owner-rv7-list-server@matronics.com] On Behalf Of Charles Becker
Subject: RV7-List: Fw: RV8-List: R-710 Hole Edge Distance
--> RV7-List message posted by: "Charles Becker" <ctbecker@charter.net>
> --> RV8-List message posted by: "Charles Becker"
<ctbecker@charter.net>
>
> When I trimmed my R-710 - Rudder Horn Brace - then match drilled the
holes
through the skin (4 on each side), the edge distance to the holes came
out
at 1/8 inch. It looks a little close to the edge. Do you think I need
to
reorder the part?
>
> Charles Becker
> N474CB - RV8A
> Empennage
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|