---------------------------------------------------------- RV7-List Digest Archive --- Total Messages Posted Fri 11/07/03: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 07:15 PM - Fw: RV8-List: R-710 Hole Edge Distance (Charles Becker) 2. 07:29 PM - A GUIDE TO AIRCRAFT PAINTING & CORROSION CONTROL (Garey Wittich) 3. 07:41 PM - Re: Fw: RV8-List: R-710 Hole Edge Distance (Radomir Zaric) ________________________________ Message 1 _____________________________________ Time: 07:15:52 PM PST US From: "Charles Becker" Subject: RV7-List: Fw: RV8-List: R-710 Hole Edge Distance --> RV7-List message posted by: "Charles Becker" ----- Original Message ----- From: "Charles Becker" Subject: RV8-List: R-710 Hole Edge Distance > --> RV8-List message posted by: "Charles Becker" > > When I trimmed my R-710 - Rudder Horn Brace - then match drilled the holes through the skin (4 on each side), the edge distance to the holes came out at 1/8 inch. It looks a little close to the edge. Do you think I need to reorder the part? > > Charles Becker > N474CB - RV8A > Empennage > > ________________________________ Message 2 _____________________________________ Time: 07:29:06 PM PST US From: Garey Wittich Subject: RV7-List: A GUIDE TO AIRCRAFT PAINTING & CORROSION CONTROL rv8-list@matronics.com, "rv9-list@matronics.com BAYES_60 (1.1 points) BODY": Bayesian.classifier.says.spam.probability.is.60.to.70@[score:0.6584]SUSPICIOUS_RECIPS.Similar.addresses.in.recipient.list (1.9 points) --> RV7-List message posted by: Garey Wittich SAVE YOURSELF hundreds of hours of research time and building time, by ordering the comprehensive "Guide to Painting & Corrosion Control of Aluminum and Composite Aircraft" This book took over 600+ hours of research time, by a fussy Builder. Contains 64 pages of the latest, practical information - summarized and gathered from MIL Standards, Paint Shops, Builders like you (what worked or didn't), Airframe Mfgs, etc. Covers Products (characteristics & application of) from PP&G, Dupont, Sherwin W'ms, Sterling, Poly Fiber, Deft, Randolph Paints, PRC De Soto, US Paints, Aircraft Finishing Systems, Tempo, 3M, etc. Some of the Topics covered in the 30 Sections are: * Aircraft Paints vs Auto Paints and Other Considerations * Corrosion Control * Spray Guns - selecting, adjusting, using and painting problems * Brushes / Rollers used with Primers & Paints * Prep Methods for Painting - Fiberglass, Steel and Aluminum * Epoxy Primers for Aluminum - MIL & Commercial, Solvent & Water Reducible * Primers for Fiberglass & Steel * Wash Primers & Self Etching Primers * Other Primers - Zinc Chromate,Zinc Oxide, Enamel * Paint Types: MIL & Non MIL Polyurethanes Enamel Types Acrylics - Lacquers & Enamels * Acid Etch / Conversion Coatings (Alodine) * Criteria for selecting a Paint Shop * 3M Cleaning Pads, Liquid Cleaners and their effectiveness * Paint Booths and their Construction * References - MIL Standards & Tech Orders * Directory of Aircraft Paint Mfgs, Distrib- utors, etc. E-Mail addresses, Phone Numbers, Application Notes YOUR AIRPLANE is judged by it's Paint Job and it is costly too, so have the latest "Information" in order to make good decisions. Contains plenty of "Do's" and "Don'ts" that save Time, Money and Frustration. Order today. Send a check for $25 to (includes Postage within the US) to: Garey Wittich 58 Village Parkway Santa Monica, CA. 90405 __________________________________ ________________________________ Message 3 _____________________________________ Time: 07:41:49 PM PST US Subject: RE: RV7-List: Fw: RV8-List: R-710 Hole Edge Distance From: "Radomir Zaric" --> RV7-List message posted by: "Radomir Zaric" Charles, You are measuring from the center of the hole, right? Just checked mine.. right around 1/4" edge distance (from the center). If you had it clecoed together properly.. it'd be hard to drill it incorrectly. HTH> Radomir RV-7A Emp. -----Original Message----- From: owner-rv7-list-server@matronics.com [mailto:owner-rv7-list-server@matronics.com] On Behalf Of Charles Becker Subject: RV7-List: Fw: RV8-List: R-710 Hole Edge Distance --> RV7-List message posted by: "Charles Becker" > --> RV8-List message posted by: "Charles Becker" > > When I trimmed my R-710 - Rudder Horn Brace - then match drilled the holes through the skin (4 on each side), the edge distance to the holes came out at 1/8 inch. It looks a little close to the edge. Do you think I need to reorder the part? > > Charles Becker > N474CB - RV8A > Empennage > >