Today's Message Index:
----------------------
1. 04:49 PM - I made a donation & I'm registering as a Marrow donor (C. Rabaut)
2. 09:29 PM - Re: Adding an access panel to the wing (jgburns)
3. 10:51 PM - Re: Adding an access panel to the wing (Dan Checkoway)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
<rv4-list@matronics.com>, <rv3-list@matronics.com>,
<rocket-list@matronics.com>,
"<aerobatic-list@matronics.com>"
<rv7-list@matronics.com>,
<rv6-list@matronics.com>
| Subject: | I made a donation & I'm registering as a Marrow donor |
--> RV7-List message posted by: "C. Rabaut" <crabaut@coalinga.com>
Okay Guys (and Gals),
Donating was the EASY part (you can do it too, it will only hurt when my wife
aka "my banker" finds out). I also did some soul searching, cuz' it's gonna
take a lot of time & traveling, but I decided I'm gonna be tested as a donor.
I just registered and now I wait to get an appointment to be tested. I gotta
go up to Stanford Medical Center (it's the closest donor center to me) and
I'll let you all know how it goes.
I hope some other folks will consider taking the plunge, either donating $
or becoming a blood/marrow donor or both... ya'll know it's for good/deserving
people.
check out
http://www.marrow.org/HELP/join_the_registry.html
or
www.transplants.org
Take Care and Take Air my friends,
Chuck
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Adding an access panel to the wing |
--> RV7-List message posted by: "jgburns" <jgburns@comcast.net>
Dan,
Great tip! Thanks and thanks to your friend Tom as well.
One confusing point for me (maybe it's the late hour) that could some clarification:
You say (on your website), "Tom commented that you want about 1/16" gap all around
the edges of the covers. Let proseal flow in there, and that helps form a
real "embedded" seal where the covers kind of sink into it."
1/16" gap? Since a picture is worth a thousand words, can you post one? Otherwise,
a few more words might help.
Cheers,
John
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Adding an access panel to the wing |
--> RV7-List message posted by: "Dan Checkoway" <dan@rvproject.com>
I haven't gotten there yet, but I will definitely put photos on the site
when I do.
The idea is that the cover plate is 1/16" smaller than the opening. Right
before riveting the reinforcement rings onto the skin, you cover the rings
in proseal. Rivet 'em. Then push the cover plate down into the proseal,
and it'll ooze out that 1/16" gap. Clean off the excess and let it dry.
You're left with the proseal having "risen" in that 1/16" gap to be flush
with the skin and cover. It's a homemade gasket.
I'm sure photos would still make this clearer, but hopefully this
explanation helps.
)_( Dan
RV-7 N714D
http://www.rvproject.com
----- Original Message -----
From: "jgburns" <jgburns@comcast.net>
Subject: Re: RV7-List: Adding an access panel to the wing
> --> RV7-List message posted by: "jgburns" <jgburns@comcast.net>
>
> Dan,
> Great tip! Thanks and thanks to your friend Tom as well.
> One confusing point for me (maybe it's the late hour) that could some
clarification:
>
> You say (on your website), "Tom commented that you want about 1/16" gap
all around the edges of the covers. Let proseal flow in there, and that
helps form a real "embedded" seal where the covers kind of sink into it."
>
> 1/16" gap? Since a picture is worth a thousand words, can you post one?
Otherwise, a few more words might help.
>
> Cheers,
> John
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|