Today's Message Index:
----------------------
1. 10:07 AM - ()
2. 11:17 AM - Bellcrank Jig W-730 (Jim Thorne)
3. 12:33 PM - Re: Bellcrank Jig W-730 (Mickey Billings)
4. 01:01 PM - Re: Bellcrank Jig W-730 (Richard Tasker)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV7-List message posted by: <farmerrd@sbcglobal.net>
I have a new in box(not overhauled) Marvel Schebler SPA-4-5 model 10-3878 carburetor
that came with a new Lyc O360-A1A. Since I used a pressure carburetor
I am selling this one which came new with the engine. $900.00 815-467-5046
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Bellcrank Jig W-730 |
--> RV7-List message posted by: "Jim Thorne" <rv7a@cox.net>
This part is shown on Drawing 13A. It says (Remove before flight) I can't figure
out what it is for. Does it have to be in place for rigging? The only mention
I've seen is on this drawing. Any help is appreciated.
Do not archive
Jim Thorne
7A QB CHD
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Bellcrank Jig W-730 |
--> RV7-List message posted by: "Mickey Billings" <mbilli@cox.net>
Jim the correct page is 15A zone E2. The device is a jig for rigging the
ailerons and then removed. You should have received one with your kit.
Mick & Jerry
----- Original Message -----
From: "Jim Thorne" <rv7a@cox.net>
Subject: RV7-List: Bellcrank Jig W-730
> --> RV7-List message posted by: "Jim Thorne" <rv7a@cox.net>
>
> This part is shown on Drawing 13A. It says (Remove before flight) I
can't figure out what it is for. Does it have to be in place for rigging?
The only mention I've seen is on this drawing. Any help is appreciated.
>
> Do not archive
>
> Jim Thorne
> 7A QB CHD
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Bellcrank Jig W-730 |
--> RV7-List message posted by: Richard Tasker <retasker@optonline.net>
This part is a temporary fixture to allow proper adjustment of the
aileron. You just clamp it into place and it puts the bellcrank in the
proper "center" position so you can adjust the pushrods. When you are
done with the first wing, you remove it and use it on the other wing.
Then take it out.
It is a good idea to keep it since you may want to adjust things more
than once. But when you are finished with your plane, in is no longer
necessary.
Dick Tasker
Jim Thorne wrote:
>--> RV7-List message posted by: "Jim Thorne" <rv7a@cox.net>
>
>This part is shown on Drawing 13A. It says (Remove before flight) I can't figure
out what it is for. Does it have to be in place for rigging? The only mention
I've seen is on this drawing. Any help is appreciated.
>
>Do not archive
>
>Jim Thorne
>7A QB CHD
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|