----------------------------------------------------------
                           RV7-List Digest Archive
                                      ---
                     Total Messages Posted Thu 07/15/04: 4
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 10:07 AM -   ()
     2. 11:17 AM - Bellcrank Jig W-730  (Jim Thorne)
     3. 12:33 PM - Re: Bellcrank Jig W-730  (Mickey Billings)
     4. 01:01 PM - Re: Bellcrank Jig W-730  (Richard Tasker)
 
 
 
________________________________  Message 1  _____________________________________


Time: 10:07:50 AM PST US
From: <farmerrd@sbcglobal.net>
Subject: RV7-List: 

--> RV7-List message posted by: <farmerrd@sbcglobal.net>

I have a new in box(not overhauled) Marvel Schebler SPA-4-5  model 10-3878 carburetor
that came with a new Lyc O360-A1A.  Since I used a pressure carburetor
I am selling this one which came new with the engine.  $900.00  815-467-5046






________________________________  Message 2  _____________________________________


Time: 11:17:19 AM PST US
From: "Jim Thorne" <rv7a@cox.net>
Subject: RV7-List: Bellcrank Jig W-730

--> RV7-List message posted by: "Jim Thorne" <rv7a@cox.net>

This part is shown on Drawing 13A.  It says (Remove before flight)  I can't figure
out what it is for.  Does it have to be in place for rigging?  The only mention
I've seen is on this drawing.  Any help is appreciated.

Do not archive

Jim Thorne
7A QB CHD






________________________________  Message 3  _____________________________________


Time: 12:33:34 PM PST US
From: "Mickey Billings" <mbilli@cox.net>
Subject: Re: RV7-List: Bellcrank Jig W-730

--> RV7-List message posted by: "Mickey Billings" <mbilli@cox.net>

Jim the correct page is 15A zone E2.  The device is a jig for rigging the
ailerons and then removed.  You should have received one with your kit.

Mick & Jerry

----- Original Message ----- 
From: "Jim Thorne" <rv7a@cox.net>
Subject: RV7-List: Bellcrank Jig W-730


> --> RV7-List message posted by: "Jim Thorne" <rv7a@cox.net>
>
> This part is shown on Drawing 13A.  It says (Remove before flight)  I
can't figure out what it is for.  Does it have to be in place for rigging?
The only mention I've seen is on this drawing.  Any help is appreciated.
>
> Do not archive
>
> Jim Thorne
> 7A QB CHD
>
>






________________________________  Message 4  _____________________________________


Time: 01:01:06 PM PST US
From: Richard Tasker <retasker@optonline.net>
Subject: Re: RV7-List: Bellcrank Jig W-730

--> RV7-List message posted by: Richard Tasker <retasker@optonline.net>

This part is a temporary fixture to allow proper adjustment of the 
aileron.  You just clamp it into place and it puts the bellcrank in the 
proper "center" position so you can adjust the pushrods.  When you are 
done with the first wing, you remove it and use it on the other wing.   
Then take it out.

It is a good idea to keep it since you may want to adjust things more 
than once.  But when you are finished with your plane, in is no longer 
necessary.

Dick Tasker

Jim Thorne wrote:

>--> RV7-List message posted by: "Jim Thorne" <rv7a@cox.net>
>
>This part is shown on Drawing 13A.  It says (Remove before flight)  I can't figure
out what it is for.  Does it have to be in place for rigging?  The only mention
I've seen is on this drawing.  Any help is appreciated.
>
>Do not archive
>
>Jim Thorne
>7A QB CHD
>
>
>  
>