Today's Message Index:
----------------------
 
     1. 07:36 AM - Horizontal Stab Rear Spar (Daniel Storer)
     2. 11:14 AM - Re: Horizontal Stab Rear Spar (Ken & Terri Howell)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
07:36:55 AM PST US
From: 
"Daniel Storer" <dstorer@okwifi.com>
Subject: 
Horizontal Stab Rear Spar
      
      --> RV7-List message posted by: "Daniel Storer" <dstorer@OKWiFi.com>
      
      Well, I just got my Empennage Kit and I'm hard at it drilling out the
      Horizontal Stab's.  Question, on drawing 3 at the AFT Exploded ISO View (3B)
      there is a note to "Trim horz. Stab rear spar to allow for elevator control
      horns to pivot...(see DWG 27A)".  I looked at DWG 27A and can see the
      bearing and horns but no callout for a trim dimension.  Is this trimmed
      during assembly for clearance?
      
      
      Thanks,
      
      
      Dan Storer
      
      RV7A newbie
      
      Oklahoma City
      
      
      
      
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
11:14:21 AM PST US
From: 
"Ken & Terri Howell" <tandk_howell@comcast.net>
Subject: 
Horizontal Stab Rear Spar
      
      --> RV7-List message posted by: "Ken & Terri Howell" <tandk_howell@comcast.net>
      
      Dan,
      
      I'm also an RV-7 newbie, but I believe the dimension you are looking for is
      on DWG 3, where it is shown as "~1" which I take to mean approximately one
      inch. That's one inch off each side. It would be easiest to do before you
      rivet the rear spar together, don't wait 'till afterward like I did.
      
      Ken Howell
      
      -----Original Message-----
      From: owner-rv7-list-server@matronics.com
      [mailto:owner-rv7-list-server@matronics.com] On Behalf Of Daniel Storer
      Subject: RV7-List: Horizontal Stab Rear Spar
      
      --> RV7-List message posted by: "Daniel Storer" <dstorer@OKWiFi.com>
      
      Well, I just got my Empennage Kit and I'm hard at it drilling out the
      Horizontal Stab's.  Question, on drawing 3 at the AFT Exploded ISO View (3B)
      there is a note to "Trim horz. Stab rear spar to allow for elevator control
      horns to pivot...(see DWG 27A)".  I looked at DWG 27A and can see the
      bearing and horns but no callout for a trim dimension.  Is this trimmed
      during assembly for clearance?
      
      
      Thanks,
      
      
      Dan Storer
      
      RV7A newbie
      
      Oklahoma City
      
      
      
      
      
      








Other Matronics Email List Services




Post A New Message
  
rv7-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/RV7-List.htm
Full Archive Search Engine
  
http://www.matronics.com/search
7-Day List Browse
  
http://www.matronics.com/browse/rv7-list
Browse RV7-List Digests
  
http://www.matronics.com/digest/rv7-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contributions









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --