Today's Message Index:
----------------------
1. 04:45 AM - glueing rudder aft edge (Don Hall)
2. 05:51 AM - Fitting/aligning the flaps/ailerons (David E. Nelson)
3. 07:32 AM - Re: Fitting/aligning the flaps/ailerons 15, 2004) at 06/07/2005 07:50:04 AM, Serialize by Router on MailServ58-US/AUS/H/NIC(Release 6.5.3FP1|December 15, 2004) at 06/07/2005 07:50:07 AM, Serialize complete at 06/07/2005 07:50:07 AM (Hinde, Frank George (Corvallis))
4. 07:35 AM - Re: glueing rudder aft edge (Hinde, Frank George (Corvallis))
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | glueing rudder aft edge |
--> RV7-List message posted by: "Don Hall" <dhall@donka.net>
I don't feel like doing pro-seal. Any other glues you'd recommend for this
job? Preferrably something at home depot or ace...
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Fitting/aligning the flaps/ailerons |
15, 2004) at 06/07/2005 07:50:04 AM,
Serialize by Router on MailServ58-US/AUS/H/NIC(Release 6.5.3FP1|December
15, 2004) at
06/07/2005 07:50:07 AM,
Serialize complete at 06/07/2005 07:50:07 AM
--> RV7-List message posted by: "David E. Nelson" <david.nelson@pobox.com>
Dan, Norman, and Frank,
Thanks for the responses. Got the right aileron squared away yesterday evening
and started on the flap hinge using a #41 drill (as that is what seemed to fit
dimpled holes) to initially mark the holes on the hinge and then followed up
with a #40. Edge distance is Ok and I think it'll all work out just fine. If
not, I can always order some more hinge and try again. ;) A couple of lessons
have been learned from this experience and that's a good thing - I just hope
that if I do this all over again many years from now I'll remember them.
Thanks again,
/\/elson
RV-7A - Flaps and ailerons
Austin, TX
--
~~ ** ~~ 4 out of 3 people have problems with fractions ~~ ** ~~
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Fitting/aligning the flaps/ailerons 15, 2004) at 06/07/2005 |
07:50:04 AM, Serialize by Router on MailServ58-US/AUS/H/NIC(Release
6.5.3FP1|December 15, 2004) at 06/07/2005 07:50:07 AM, Serialize complete
at 06/07/2005 07:50:07 AM
--> RV7-List message posted by: "Hinde, Frank George (Corvallis)" <frank.hinde@hp.com>
You will have no chance of remembering...I have built a metal plane
before about 5 years ago and still I am amazed at some of the screw ups
I've made...Maybe its age...:)
All the best David
Frank
Do not archive
-----Original Message-----
From: owner-rv7-list-server@matronics.com
[mailto:owner-rv7-list-server@matronics.com] On Behalf Of David E.
Nelson
Subject: RV7-List: Fitting/aligning the flaps/ailerons 15, 2004) at
06/07/2005 07:50:04 AM, Serialize by Router on
MailServ58-US/AUS/H/NIC(Release 6.5.3FP1|December 15, 2004) at
06/07/2005 07:50:07 AM, Serialize complete at 06/07/2005 07:50:07 AM
--> RV7-List message posted by: "David E. Nelson"
--> <david.nelson@pobox.com>
Dan, Norman, and Frank,
Thanks for the responses. Got the right aileron squared away yesterday
evening and started on the flap hinge using a #41 drill (as that is what
seemed to fit dimpled holes) to initially mark the holes on the hinge
and then followed up with a #40. Edge distance is Ok and I think it'll
all work out just fine. If not, I can always order some more hinge and
try again. ;) A couple of lessons have been learned from this
experience and that's a good thing - I just hope that if I do this all
over again many years from now I'll remember them.
Thanks again,
/\/elson
RV-7A - Flaps and ailerons
Austin, TX
--
~~ ** ~~ 4 out of 3 people have problems with fractions ~~ ** ~~
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | glueing rudder aft edge |
--> RV7-List message posted by: "Hinde, Frank George (Corvallis)" <frank.hinde@hp.com>
Vulkem 116 sealant sold at Home Depot....It is THE duct sealant used by
all my contractors for a large wafer fab...When it sets up it sticks
like you won't believe and stays gooey.
Oh and is perfectly compatible with Aluminium.
Frank
-----Original Message-----
From: owner-rv7-list-server@matronics.com
[mailto:owner-rv7-list-server@matronics.com] On Behalf Of Don Hall
Subject: RV7-List: glueing rudder aft edge
--> RV7-List message posted by: "Don Hall" <dhall@donka.net>
I don't feel like doing pro-seal. Any other glues you'd recommend for
this job? Preferrably something at home depot or ace...
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|