Today's Message Index:
----------------------
 
     1. 09:07 AM - Map Box (Hinde, Frank George (Corvallis))
     2. 09:48 AM - Re: Map Box (Dan Checkoway)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
09:07:55 AM PST US
Subject: 
Map Box
From: 
"Hinde, Frank George (Corvallis)" <frank.hinde@hp.com>
      
      --> RV7-List message posted by: "Hinde, Frank George (Corvallis)" <frank.hinde@hp.com>
      
       Hi guys,
      
      The drawing for the map box shows cut out's in two different location on
      the instrument pnel depending on whether it is a tip-up or slider
      canopy.
      
      The tip up is shown lower on theinstrument  panel than the slider.
      
      I have a tip up but want to pit the map box up higher like on the slider
      to fit the Dynon engine instrument under the map box. It will fit but
      only if the map box is up higher.
      
      I can't see any reason the map box can't go up high but wondered if
      anyone had any actual experience on this...i did phone Van's but guess
      where they are?..:)
      
      Thanks
      
      Frank
      
      
      
      
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
09:48:23 AM PST US
From: 
"Dan Checkoway" <dan@rvproject.com>
Subject: 
Re: Map Box
      
      --> RV7-List message posted by: "Dan Checkoway" <dan@rvproject.com>
      
      The tip up frame, the C channel at the front of the canopy, comes down about 
      2 or 3 inches from the top.  That's about all I can think of at the 
      moment...
      
      )_( Dan
      RV-7 N714D
      http://www.rvproject.com
      
      ----- Original Message ----- 
      From: "Hinde, Frank George (Corvallis)" <frank.hinde@hp.com>
      Subject: RV7-List: Map Box
      
      
      > --> RV7-List message posted by: "Hinde, Frank George (Corvallis)" 
      > <frank.hinde@hp.com>
      >
      > Hi guys,
      >
      > The drawing for the map box shows cut out's in two different location on
      > the instrument pnel depending on whether it is a tip-up or slider
      > canopy.
      >
      > The tip up is shown lower on theinstrument  panel than the slider.
      >
      > I have a tip up but want to pit the map box up higher like on the slider
      > to fit the Dynon engine instrument under the map box. It will fit but
      > only if the map box is up higher.
      >
      > I can't see any reason the map box can't go up high but wondered if
      > anyone had any actual experience on this...i did phone Van's but guess
      > where they are?..:)
      >
      > Thanks
      >
      > Frank
      >
      >
      > 
      
      
      
      
      
      








Other Matronics Email List Services




Post A New Message
  
rv7-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/RV7-List.htm
Full Archive Search Engine
  
http://www.matronics.com/search
7-Day List Browse
  
http://www.matronics.com/browse/rv7-list
Browse RV7-List Digests
  
http://www.matronics.com/digest/rv7-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contributions









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --