Today's Message Index:
----------------------
1. 03:46 AM - Re: 5pt harness kit for sale (Wndwlkr1228@aol.com)
2. 07:01 AM - Re: finishing kit timing and options. (Hinde, Frank George (Corvallis))
3. 05:08 PM - Re: 5pt harness kit for sale (Don Hall)
4. 05:15 PM - Matronics Email List Web Server Upgrade Tonight... (Matt Dralle)
5. 05:49 PM - Re: 5pt harness kit for sale (Wndwlkr1228@aol.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 5pt harness kit for sale |
Don,
I will take the kit, if it is still available. I understand that they can be
modified to fit a 6A with little trouble. My wife can pay for it with
PayPal, if that is acceptable.
George Stanley
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | finishing kit timing and options. |
I have not flown yet but the cowl looks awesome. it will take you
moretime to fit. About the worst combination to make it fit is the
Airflow Performance fuel injection servo, FF sump...I have a 2.25
(slightly shorter than listed) and there was no way I could fit the
James alternate air setup...Its debatable that you need it anyway (with
FI) but I am running without alternate air for the first flights at
least.
I can fit a buterfly valve and make a non return valve for the alternate
air if desired but it will take time and head scratching.
You would be much better off with the Bendix servo if going with FF sump
or go for Verticle induction and live with the pig's snout that you bond
on the bottom of the cowl.
See my Yahoo group on the James cowl.
Frank
________________________________
[mailto:owner-rv7-list-server@matronics.com] On Behalf Of Don Hall
Sent: Saturday, July 29, 2006 10:11 AM
I'm now drilling the longerons on my upside down fuse.
I'm thinking it's about time to order that finishing kit.
Also, are there better canopy choices (tint/thickness)?
And for the RV7, any feedback on the Sam James cowl?
other mod suggestions that might effect kit ordering?
thanks
******************************************
Don Hall
N517DG (registered)
rv7 fuselage
http://rv7.donka.net <http://rv7.donka.net/>
******************************************
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 5pt harness kit for sale |
It's yours. Send me an address and I'll mail it. If you want some pics of
mine during installation:
http://donka.net/gallery/view_album.php?set_albumName=rv7fusecentersection
<http://donka.net/gallery/view_album.php?set_albumName=rv7fusecentersection&
page=2> &page=2
paypal will be fine. I'll check with my wife to get her paypal acct.
******************************************
Don Hall
N517DG (registered)
rv7 fuselage
http://rv7.donka.net <http://rv7.donka.net/>
******************************************
_____
[mailto:owner-rv7-list-server@matronics.com] On Behalf Of
Wndwlkr1228@aol.com
Sent: Monday, July 31, 2006 6:43 AM
Don,
I will take the kit, if it is still available. I understand that they can
be modified to fit a 6A with little trouble. My wife can pay for it with
PayPal, if that is acceptable.
George Stanley
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Matronics Email List Web Server Upgrade Tonight... |
--> RV7-List message posted by: Matt Dralle <dralle@matronics.com>
Dear Listers,
This evening I will be upgrading the Matronics Web Server hardware to a new Quad-processor
2.8Ghz Xeon system (yes, 4-physical CPUs!) with an Ultra 320 SCSI
Raid 5 disk system and 5GB of DDR2 RAM.
As with the older system, the new system will be running the latest version of
Redhat Linux. Most of the software configuration work is already done for the
migration, but I still have to sync all of the archive and forum data from the
old system to the new system. I am anticipating about 2 to 3 hours of downtime
for me to fully make the transition, although it could be considerable less
if everything goes according to plan.
The Matronics Webserver will be *UNavailable* from the Internet during the work,
and you will receive a time-out if you try to connect during the upgrade.
Email List Distribution will be *available* during the upgrade of the Web Server,
and List message distribution will function as normal.
This represents a significant performance upgrade for the Matronics Web Server
and you should notice nicely improved searching and surfing performance following
the upgrade!
Best regards,
Matt Dralle
Matronics Email List Administrator
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 5pt harness kit for sale |
Don,
Thanks for the response! My address is as follows:
George Stanley
5136 Antelope Dr.
Fort Mohave, AZ.
86426
Let me know what the total is and I will take care of the bill.
Great pics, by the way. They will help since the RV-6A was not included in
the original 5pt harness design.
George
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|