Today's Message Index:
----------------------
1. 08:04 AM - Quick build question (J. Brunke)
2. 09:20 AM - Re: Quick build question (Scott R. Shook)
3. 09:50 AM - Re: Quick build question (Darrell Reiley)
4. 06:08 PM - Re: Quick build question (Bill Schlatterer)
5. 10:31 PM - Re: Quick build question (J. Brunke)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Quick build question |
The quickbuild is truly a great head start towards an airplane. The
only negative to it, is that you have to figure out what Van's has and
has not done. Obviously that can be accomplished in a relatively short
time. While going through the drawings yesterday and checking off what
has been done, I noticed on Drawing 34 that there are 12 AN - 4 bolts
that go through the F704 center section. While the top bolts will be
easy to tighten, the bottom row will be a little "challenging". Just
curious if any of you remember if these bolts were already in place when
you got your
QB kit?
Thanks,
John Brunke
RV7 tip-up slowly moving along.
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Quick build question |
I too would be interested as my QB fuse just arrived on Saturday
Scott R. Shook
RV-7A (Building)
N696JS (Reserved)
_____
From: owner-rv7-list-server@matronics.com
[mailto:owner-rv7-list-server@matronics.com] On Behalf Of J. Brunke
Sent: Friday, July 13, 2007 09:04
Subject: RV7-List: Quick build question
The quickbuild is truly a great head start towards an airplane. The only
negative to it, is that you have to figure out what Van's has and has not
done. Obviously that can be accomplished in a relatively short time.
While going through the drawings yesterday and checking off what has been
done, I noticed on Drawing 34 that there are 12 AN - 4 bolts that go through
the F704 center section. While the top bolts will be easy to tighten, the
bottom row will be a little "challenging". Just curious if any of you
remember if these bolts were already in place when you got your
QB kit?
Thanks,
John Brunke
RV7 tip-up slowly moving along.
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Quick build question |
Take nothing for granted! Start at the front of each
section of the instructions for the wing and fuse if
QB and go through the motions. You'll need to know
these parts as things come together anyway.
Darrell
--- "Scott R. Shook" <sshook@cox.net> wrote:
> I too would be interested as my QB fuse just arrived
> on Saturday
>
>
>
>
> Scott R. Shook
> RV-7A (Building)
> N696JS (Reserved)
>
> _____
>
> From: owner-rv7-list-server@matronics.com
> [mailto:owner-rv7-list-server@matronics.com] On
> Behalf Of J. Brunke
> Sent: Friday, July 13, 2007 09:04
> To: rv7-list@matronics.com
> Subject: RV7-List: Quick build question
>
>
>
> The quickbuild is truly a great head start towards
> an airplane. The only
> negative to it, is that you have to figure out what
> Van's has and has not
> done. Obviously that can be accomplished in a
> relatively short time.
> While going through the drawings yesterday and
> checking off what has been
> done, I noticed on Drawing 34 that there are 12 AN -
> 4 bolts that go through
> the F704 center section. While the top bolts will
> be easy to tighten, the
> bottom row will be a little "challenging". Just
> curious if any of you
> remember if these bolts were already in place when
> you got your
>
> QB kit?
>
>
>
> Thanks,
>
> John Brunke
>
> RV7 tip-up slowly moving along.
>
>
>
>
>
>
>
>
>
Be a better Heartthrob. Get better relationship answers from someone who knows.
Yahoo! Answers - Check it out.
http://answers.yahoo.com/dir/?link=list&sid=396545433
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Quick build question |
John, I think I remember getting my wife to start the nuts as she could get
her hand down in the center section. A long set of forceps would work too.
Bill S
7a
_____
From: owner-rv7-list-server@matronics.com
[mailto:owner-rv7-list-server@matronics.com] On Behalf Of J. Brunke
Sent: Friday, July 13, 2007 11:04 AM
Subject: RV7-List: Quick build question
The quickbuild is truly a great head start towards an airplane. The only
negative to it, is that you have to figure out what Van's has and has not
done. Obviously that can be accomplished in a relatively short time.
While going through the drawings yesterday and checking off what has been
done, I noticed on Drawing 34 that there are 12 AN - 4 bolts that go through
the F704 center section. While the top bolts will be easy to tighten, the
bottom row will be a little "challenging". Just curious if any of you
remember if these bolts were already in place when you got your
QB kit?
Thanks,
John Brunke
RV7 tip-up slowly moving along.
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Quick build question |
Thanks Bill. I used an open end wrench with a piece of tape covering
one end with the nut stuck inside. Then used a crescent wrench
to make an extension for the wrench. I had a good friend help me.
The reason he's a good friend, was after we put on three bolts
this way, I realized that a washer gets put on the bolt side also. I
think that's one of the few places I have seen that so far on the kit.
Of course we had the learning curve down by then and it didn't take
quite as long to put them on a second time. It's funny how little
things
like that all of a sudden "appear" on the drawing. At least it wasn't
an expensive mistake.
Thanks,
John
----- Original Message -----
From: Bill Schlatterer
To: rv7-list@matronics.com
Sent: Friday, July 13, 2007 7:08 PM
Subject: RE: RV7-List: Quick build question
John, I think I remember getting my wife to start the nuts as she
could get her hand down in the center section. A long set of forceps
would work too.
Bill S
7a
-------------------------------------------------------------------------
-----
From: owner-rv7-list-server@matronics.com
[mailto:owner-rv7-list-server@matronics.com] On Behalf Of J. Brunke
Sent: Friday, July 13, 2007 11:04 AM
To: rv7-list@matronics.com
Subject: RV7-List: Quick build question
The quickbuild is truly a great head start towards an airplane. The
only negative to it, is that you have to figure out what Van's has and
has not done. Obviously that can be accomplished in a relatively short
time. While going through the drawings yesterday and checking off what
has been done, I noticed on Drawing 34 that there are 12 AN - 4 bolts
that go through the F704 center section. While the top bolts will be
easy to tighten, the bottom row will be a little "challenging". Just
curious if any of you remember if these bolts were already in place when
you got your
QB kit?
Thanks,
John Brunke
RV7 tip-up slowly moving along.
href="http://www.matronics.com/Navigator?RV7-List">http://www.matronics
.com/Navigator?RV7-List
href="http://forums.matronics.com">http://forums.matronics.com
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|