Today's Message Index:
----------------------
1. 05:35 AM - Re: Superior forward facing sump on an RV-7A (Duncan Engh)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Superior forward facing sump on an RV-7A |
Thanks from Red Wing,Minnesota
Duncan 7A
--- On Fri, 6/27/08, Greg Blakey <gblakey@vic.australis.com.au> wrote:
From: Greg Blakey <gblakey@vic.australis.com.au>
Subject: Re: RV7-List: Superior forward facing sump on an RV-7A
Gents,
-
One thing you might like to consider rather than going to the expense of a
whole new cable are these threaded connectors from Aircraft Spruce.-- D
an Checkaway used one and I have purchased for my M1B setup to an Aerosance
Throttle Body.
-
Here is the link if anyone is interested and by just choosing the additiona
l length you require, you can thread this to the end of your existing cable
.
-
http://www.aircraftspruce.com/search/search.php?query=10376&searchsubmit
=Search&search=1
-
Cheers from Down Under!
-
Greg(RV-7........wiring)
-
----- Original Message -----
From: Duncan Engh
Sent: Friday, June 27, 2008 10:08 PM
Subject: Re: RV7-List: Superior forward facing sump on an RV-7A
Please forward the address for ACS
Thank you
Duncan Engh
--- On Fri, 6/27/08, Andrew Phillips <andrew.phillips@sympatico.ca> wrote:
From: Andrew Phillips <andrew.phillips@sympatico.ca>
Subject: Re: RV7-List: Superior forward facing sump on an RV-7A
Jason, I had the same problem but the new exhaust fixed it. I have a quick
drain and it goes out a hole on the pilots -side of the sump not out the
bottom. The cables that Van's sold were too short for me and so I am gettin
g ACS to make longer ones. This will depend on what fuel injection system y
ou are using. I have the Airflow Performance unit. I made my own throttle/m
ix bracket. I will try to remember to take a pic the next time I am at the
airport. If you don't get one by the end of the weekend send me a reminder.
Andrew Phillips
On 26-Jun-08, at 5:12 PM, jkrowe.1@netzero.net wrote:
I recently mounted my engine on my RV-7A and found that I had a couple of p
roblems.- I have the forward facing Superior sump, the new non-Ryton one,
and found that it interfered with my drain plug and came very close to the
number one intake lead/runner.- After talking to Vettermans, they said t
hat the M1B-exhaust that Vans had sent me-would not work.- The new fo
rward facing sump has the same basic architecture as the Ryton sump and fro
m what I understand, Vans was somewhat confused about this and sent the MIB
.- So I am exhanging the MIB exhaust with the Superior exhaust from Van's
to correct the problem.-
I was wanting to know if anyone out there has a Superior forward facing sum
p with a Vettermans crossover exhaust on a 7A installed that would be willi
ng to send a couple of pictures of their installation?- Particularly the
area around the drain plug, the area between the number one intake and exha
ust leads/runners, and then how the brackets for the throttle and mixture w
ere mounted.- Also, what length cables were used for the throttle and mix
ture?- I would appreciate any help and advice.
Jason
N338JR (Reserved)
____________________________________________________________
Fabulous Spa Getaway!
Enter for your chance to WIN great beauty prizes everyday!
href="http://www.matronics.com/Navigator?RV7-List">http://www.matronics.c
om/Navigator?RV7-List
href="http://forums.matronics.com">http://forums.matronics.com
href="http://www.matronics.com/contribution">http://www.matronics.com/con
tribution
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://www.matronics.com/Navigator?RV7-List"'>http://www.matroni
cs.com/Navigator?RV7-List
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://forums.matronics.com"'>http://forums.matronics.com
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
href='3D"http://www.matronics.com/contribution"'>http://www.matronics.com
/contribution
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
3D
=0A=0A=0A
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|