Today's Message Index:
----------------------
 
     1. 10:02 PM - Routing Elevator Trim Tab Servo Wires (Garey Wittich)
     2. 11:10 PM - Re: Routing Elevator Trim Tab Servo Wires (Matt Dralle)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
10:02:46 PM PST US
From: 
Garey Wittich <gareywittich2000@yahoo.com>
Subject: 
Routing Elevator Trim Tab Servo Wires
      
      
      Greetings:
      
      Looking for a better solution than routing the Trim Tab Servo wires thru the hole
      in the Elevator Spar (where the long Servo Motor Screw goes).
      
      Does anybody have any pictures or diagrams of the Wire Routing of the Trim Tab
      Motor wires in the Elevator to the Horizontal STABILIZER to the fuselage.
      
      Not much given on this subject on Matronics.
      
      Thanks,   Garey    Santa Monica, CA
      
      
            
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
11:10:28 PM PST US
From: 
Matt Dralle <dralle@matronics.com>
Subject: 
Re: Routing Elevator Trim Tab Servo Wires
      
      At 10:01 PM 1/24/2009  Saturday, you wrote:
      >--> RV-List message posted by: Garey Wittich <gareywittich2000@yahoo.com>
      >
      >Greetings:
      >
      >Looking for a better solution than routing the Trim Tab Servo wires thru the hole
      in the Elevator Spar (where the long Servo Motor Screw goes).
      >
      >Does anybody have any pictures or diagrams of the Wire Routing of the Trim Tab
      Motor wires in the Elevator to the Horizontal STABILIZER to the fuselage.
      >
      >Not much given on this subject on Matronics.
      >
      >Thanks,   Garey    Santa Monica, CA
      
      Hi Garey,
      
      I just did this task.  I simply drilled a 1/4" hole above the servo screw hole
      and added a little black plastic bushing.  Attached is a picture.
      
      Best regards,
      
      Matt Dralle
      RV-8 #82880 N998RV (res)
      Building Time Since July 2008: 728.75 Hours
      
      








Other Matronics Email List Services




Post A New Message
  
rv7-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/RV7-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/rv7-list
Browse RV7-List Digests
  
http://www.matronics.com/digest/rv7-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --