Today's Message Index:
----------------------
1. 03:32 PM - Front & Back Wheel Pant Fit... (Matt Dralle)
2. 10:24 PM - Re: RV-List: Front & Back Wheel Pant Fit... (Jim)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Front & Back Wheel Pant Fit... |
Dear Listers,
I'm adding the little fairings between the main wheel pants and the gear leg today.
I'm using the premade fairing from Farings Etc and installation looks pretty
straightforward.
But I'm really on the fence about the main wheel pants and specifically the front-to-back
fit. I have the gap all the way around between the two perfect. No
problems there.
The issue is with the unevenness of the thickness of the front to back. The rear
part has the flange that holds the plate nuts. The shoulder is a little bit
higher in some spots than the front part and a little be lower in other spots.
If it was higher all the way around, it would be a no-brainer to just sand
it down. But the high/low is problematic. The low spots are generally caused
by the screws and the high spots between the screws.
Yeah, I could fill and sand and fill and sand so that *maybe* I would have a "perfect"
transition front to back. But maybe not. I'm thinking its going to be
a huge amount of work that, in the end, isn't really going to look any different
once its painted.
Should I just embrace the transition as-is and move on? Or spend a couple of weeks
trying to fill and sand in hopes of a better look?
Attached are a couple of pics of what it looks like currently.
Thanks!
Matt Dralle
RV-8 #82880 N998RV
http://www.mattsrv8.com - Matt's RV-8 Construction Blog
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV-List: Front & Back Wheel Pant Fit... |
Had the same when doing mine a few years ago. Spent about four days filling
and sanding for that right fit. Looking at them now it was worth the effort.
Hang in there Matt, my guess is you'll like the outcome.
Yes building an OBAM aircraft is "a huge amount of work" but you knew that
when you signed on.
I'm Sure you'll be proud of the extra effort.
Keep at it, not far now,
Jim in Kelowna RV6-A C-GIIG for sale (No license)
----- Original Message -----
From: "Matt Dralle" <dralle@matronics.com>
<rv7-list@matronics.com>
Sent: Saturday, January 30, 2010 3:31 PM
Subject: RV-List: Front & Back Wheel Pant Fit...
>
> Dear Listers,
>
> I'm adding the little fairings between the main wheel pants and the gear
> leg today. I'm using the premade fairing from Farings Etc and
> installation looks pretty straightforward.
>
> But I'm really on the fence about the main wheel pants and specifically
> the front-to-back fit. I have the gap all the way around between the two
> perfect. No problems there.
>
> The issue is with the unevenness of the thickness of the front to back.
> The rear part has the flange that holds the plate nuts. The shoulder is a
> little bit higher in some spots than the front part and a little be lower
> in other spots. If it was higher all the way around, it would be a
> no-brainer to just sand it down. But the high/low is problematic. The
> low spots are generally caused by the screws and the high spots between
> the screws.
>
> Yeah, I could fill and sand and fill and sand so that *maybe* I would have
> a "perfect" transition front to back. But maybe not. I'm thinking its
> going to be a huge amount of work that, in the end, isn't really going to
> look any different once its painted.
>
> Should I just embrace the transition as-is and move on? Or spend a couple
> of weeks trying to fill and sand in hopes of a better look?
>
> Attached are a couple of pics of what it looks like currently.
>
> Thanks!
>
> Matt Dralle
> RV-8 #82880 N998RV
> http://www.mattsrv8.com - Matt's RV-8 Construction Blog
>
>
> E-mail message checked by Spyware Doctor (7.0.0.514)
> Database version: 6.14250
> http://www.pctools.com/en/spyware-doctor-antivirus/
>
E-mail message checked by Spyware Doctor (7.0.0.514)
Database version: 6.14250
http://www.pctools.com/en/spyware-doctor-antivirus/
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|