Today's Message Index:
----------------------
1. 05:15 AM - VM 1000 & Single Drive Dual Mag (DLN 3000) (Esten Spears)
2. 05:24 AM - VM 1000 Fuel Flowmeter & Purge Valve Installation (Esten Spears)
3. 11:47 AM - Re: (Richard Lundin)
4. 06:55 PM - skis (Mike Betti)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
<rv-list@matronics.com>
| Subject: | VM 1000 & Single Drive Dual Mag (DLN 3000) |
--> RV8-List message posted by: "Esten Spears" <ewspears@comcast.net>
Has anyone installed a VM 1000 Engine Monitor with a Single Drive Dual Mag?
If So; What Tach Sensor did you use and where and how did you mount it??????
The instructions call for it to be placed in the gear inspection port where
it picks up the passing gear teeth. The single drive dual mag has such ports
but it uses nylon gears so I don't think the sensor would see anything.
Any help would be appreciated!
Esten Spears, RV8A, 80922, N922ES (reserved), Leeward Air Ranch, Ocala, FL
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
<rv-list@matronics.com>
| Subject: | VM 1000 Fuel Flowmeter & Purge Valve Installation |
--> RV8-List message posted by: "Esten Spears" <ewspears@comcast.net>
Has anyone done an IO 360 200HP with a VM 1000 Fuel Flowmeter & Purge Valve
Installation???
If so; where and how did you place the purge valve and flowmeter????? I am using
standard Bendix Servo and Spider.
Any help would be appreciated!!
Esten Spears, RV8A, 80922, N922ES (reserved), Leeward Air Ranch, Ocala, FL
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV8-List message posted by: Richard Lundin <rlundin46@yahoo.com>
I worked with RTV alot in boat work some years ago. I
don't know of anything that breaks it down. We use to
get things loose by applying moderate pull, in this
case on the fairing, and then use a razor knife to cut
the RTV loose in several passes. Keep the pull light
to moderate and you should be fine.
Rick
--- rdaulton3@comcast.net wrote:
> --> RV8-List message posted by:
> <rdaulton3@comcast.net>
>
> Help..Help...A previous owner used RTV to seal the
> fairing around the vertical fin/horizontal stab.
> Can anyone tell me what will remove the RTV. It is
> the rubber compound used to seal around bathtubs,
> ect. Thanks much in advance.
> rdaulton3@comcast.net.
>
>
>
> Contributions
> any other
> Forums.
>
> http://www.matronics.com/chat
>
> http://www.matronics.com/subscription
> http://www.matronics.com/FAQ/RV8-List.htm
> http://www.matronics.com/archives
> http://www.matronics.com/photoshare
> http://www.matronics.com/emaillists
>
>
>
>
>
__________________________________
http://antispam.yahoo.com/tools
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> RV8-List message posted by: "Mike Betti" <mbetti@chartermi.net>
Has any one set up a RV8 with skis? I'm thinking of building one in the future
and would require them.
Mike
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|