Today's Message Index:
----------------------
1. 07:14 AM - Re: RV8-List Digest: 1 Msgs - 06/14/04 (Sally and George)
2. 08:03 AM - You`ve got 1 VoiceMessage! (Russell Johnson)
3. 09:34 PM - Re: RV8-List Digest: 3 Msgs - 06/13/04 (Richard)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | RE: RV8-List Digest: 1 Msgs - 06/14/04 |
--> RV8-List message posted by: "Sally and George" <aeronut58@hotmail.com>
Greg:
I've had problems with being unable to start a thread into a plate nut and
have used a tap to get it started.
Be careful, though! Plate nut threads are rolled, not cut (for good reason)
so be very gentle with the tap...do no more than you have to.
George
>----- Original Message -----
>From: "greg" <greg@itmack.com>
>Subject: RV8-List: screwing into platenuts
>
>
> > --> RV8-List message posted by: "greg" <greg@itmack.com>
> >
> > I'm trying to mount the electric trim and the screws won't go into the
>platenuts and I'm really laying into them and starting to bur the heads.
>Also I'm worried about stretching the skin with all the force I'm putting
>onto them.
> >
> > Is there any trick I'm missing or do I need to run a tap through the
>platenuts?
> >
> >
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | You`ve got 1 VoiceMessage! |
--> RV8-List message posted by: Russell Johnson <entec1@pld.com>
Dear Customer!
You`ve got 1 VoiceMessage from voicemessage.com website!
You can listen your Virtual VoiceMessage at the following link:
http://virt.voicemessage.com/index.listen.php2=35affv
or by clicking the attached link.
Send VoiceMessage! Try our new virtual VoiceMessage Empire!
Best regards: SNAF.Team (R).
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV8-List Digest: 3 Msgs - 06/13/04 |
--> RV8-List message posted by: "Richard" <chiefs@peak.org>
Greg,
Here is what I did... I used Boe Lube and ran a stainless steel screw
through the platenut first.
Dick White
RV-8 N94DW
Old Crow flying
Newport, OR
----- Original Message -----
From: "RV8-List Digest Server" <rv8-list-digest@matronics.com>
Subject: RV8-List Digest: 3 Msgs - 06/13/04
> *
>
> ==================================================
> Online Versions of Today's List Digest Archive
> ==================================================
>
> Today's complete RV8-List Digest can be also be found in either
> of the two Web Links listed below. The .html file includes the Digest
> formatted in HTML for viewing with a web browser and features Hyperlinked
> Indexes and Message Navigation. The .txt file includes the plain ASCII
> version of the RV8-List Digest and can be viewed with a generic
> text editor such as Notepad or with a web browser.
>
> HTML Version:
>
>
http://www.matronics.com/digest/rv8-list/Digest.RV8-List.2004-06-13.html
>
> Text Version:
>
>
http://www.matronics.com/digest/rv8-list/Digest.RV8-List.2004-06-13.txt
>
>
> ================================================
> EMail Version of Today's List Digest Archive
> ================================================
>
>
> RV8-List Digest Archive
> ---
> Total Messages Posted Sun 06/13/04: 3
>
>
> Today's Message Index:
> ----------------------
>
> 1. 02:34 AM - elevator leading edge (greg)
> 2. 02:44 PM - EIS plus what engine instrumentation? (Jack Blomgren)
> 3. 04:30 PM - screwing into platenuts (greg)
>
>
> ________________________________ Message 1
_____________________________________
>
>
> Time: 02:34:33 AM PST US
> From: "greg" <greg@itmack.com>
> Subject: RV8-List: elevator leading edge
>
> --> RV8-List message posted by: "greg" <greg@itmack.com>
>
> I'm just about to roll the leading edge of my elevators and upon checking
the plans
> the way I look at it. The top half of the elevator should be slightly
longer
> and be on the outside when riveted, so that the rivet is just a bit lower
> than half way around the leading edge.
>
> But on both of my elevators the longer edge is on the lower half. Have I
got a
> problem or am I just looking at the plans wrong?
>
>
> ________________________________ Message 2
_____________________________________
>
>
> Time: 02:44:45 PM PST US
> From: "Jack Blomgren" <jackanet@hotmail.com>
> Subject: RV8-List: EIS plus what engine instrumentation?
>
> --> RV8-List message posted by: "Jack Blomgren" <jackanet@hotmail.com>
>
> -8, 8A Drivers,
> I'm looking for good engine instrument solutions to accompany a Grand
Rapids
> EIS for the right third of my -8 panel. If you have an EIS plus
instrument
> combination you like and would recommend, I welcome your input. Thanks.
> Jack Blomgren
> -8 80%
>
> http://toolbar.msn.click-url.com/go/onm00200415ave/direct/01/
>
>
> ________________________________ Message 3
_____________________________________
>
>
> Time: 04:30:05 PM PST US
> From: "greg" <greg@itmack.com>
> Subject: RV8-List: screwing into platenuts
>
> --> RV8-List message posted by: "greg" <greg@itmack.com>
>
> I'm trying to mount the electric trim and the screws won't go into the
platenuts
> and I'm really laying into them and starting to bur the heads. Also I'm
worried
> about stretching the skin with all the force I'm putting onto them.
>
> Is there any trick I'm missing or do I need to run a tap through the
platenuts?
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|