Today's Message Index:
----------------------
1. 04:33 AM - Re: Re: Jacking RV=8 (Paul Schattauer)
2. 06:28 AM - Jacking RV-8 (RV_8 Pilot)
3. 06:59 AM - Re: Re: Jacking RV=8 (JOHN STARN)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Jacking RV=8 |
--> RV8-List message posted by: "Paul Schattauer" <chasm711@msn.com>
Jim
The wing jack works really well but if you jack both wings at the same time
be careful that the aircraft doesn't tip forward onto the prop. It's not
pretty. The jacks are available in trade a plane for about $130 apiece, you
really only need one.
Paul
>From: "Sally and George" <aeronut58@hotmail.com>
>Reply-To: rv8-list@matronics.com
>To: rv8-list@matronics.com
>Subject: RV8-List: Re: Jacking RV=8
>Date: Sun, 27 Jun 2004 22:34:09 -0500
>
>--> RV8-List message posted by: "Sally and George" <aeronut58@hotmail.com>
>
>Jim:
>
>I used a standard aircraft jack (intended for a Bonanza) on the wing
>tie-down. It has a concave top surface which the tie down ring fits nicely
>into. Its been safe and secure.
>
>George
>
>
> >
> >Time: 07:04:53 PM PST US
> >From: Jim Bean <jim-bean@att.net>
> >Subject: RV8-List: Jacking RV-8
> >
> >--> RV8-List message posted by: Jim Bean <jim-bean@att.net>
> >
> >hi all,
> >I can't seem to find a way to get a jack under the gear leg of my RV-8.
> >There isn't enough area at the bottom of the gear leg for a floor jack.
> >I can't get it close enough. Is it possible to jack under the wing?
> >What have you all done?
> >Jim Bean
> >Mounting empinage
> >
> >
>
>From will you? to I do, MSN Life Events is your resource for Getting
>Married. http://lifeevents.msn.com/category.aspx?cid=married
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
1.0 FROM_HAS_ULINE_NUMS From: contains an underline and numbers/letters
--> RV8-List message posted by: "RV_8 Pilot" <rv_8pilot@hotmail.com>
I built a wooden inverted pyramid shaped device that sits under the tie down
location. I use a bolt threaded into the tie down, through the wood, to
keep it from moving. Use a floor jack under the apex of the wooden device
to lift. Cumbersome, but I'm not comfortable with lifting at the tie down
pt alone. Not only that, but my wooden thing cost less to build than an
aircraft jack.
Bryan Jones -8
www.LoneStarSquadron.com
Houston, Texas
>hi all,
>I can't seem to find a way to get a jack under the gear leg of my RV-8.
>There isn't enough area at the bottom of the gear leg for a floor jack.
>I can't get it close enough. Is it possible to jack under the wing?
>What have you all done?
>Jim Bean
>Mounting empinage
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Jacking RV=8 |
--> RV8-List message posted by: "JOHN STARN" <jhstarn@verizon.net>
We used two wing jacks on the HRII. The top of these jacks are concave and
the tie down rings fit into them perfectly. The first time Tom & I jacked up
N561FS we were going up slowly and noticed looong before the mains started
to lift that the tail wheel was 18" off he floor. We literally tired a box
(plastic milk bottle carton) full of rocks to the tail. Would have posted
sooner but was not sure that RV-8 tie downs were at same balance point.
KABONG Do Not Archive. (GBA)
---- Original Message -----
From: "Paul Schattauer" <chasm711@msn.com>
Subject: RE: RV8-List: Re: Jacking RV=8
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|