Today's Message Index:
----------------------
1. 08:20 AM - Re: Superior engine installation (Dick Jordan)
2. 10:06 AM - Re: Superior engine installation (Jack Blomgren)
3. 10:42 AM - Heat Muff over exhaust joint (Jack Blomgren)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Superior engine installation |
--> RV8-List message posted by: "Dick Jordan" <mkejrj@erols.com>
Darren,
I installed the XP 360 with Composite Induction on my 8A. Van's IO 360
THROTTLE/MIX kit ( $95.00) worked well to mount the Mixture hardware but was
useless for the Throttle.
In order to mount the Throttle Cable I constructed a mounting platform
attaching same to the bottom of the composite Sump using the 4 threaded
holes provided by Superior. The platform spans the bottom of the sump
running from right to left and is attached to the sump with 4 safety wired
bolts.
I attached a cable termination fitting at the rear of the platform in a
position that would provide proper clearance from the sump and exhaust as
well as providing proper function of the Throttle hardware. Determining the
proper positioning for the termination fitting took several iterations but
the end result is , IMHO , quite functional.
The Throttle cable runs aft from the termination fitting ,under the
Composite Sump,and then angles up to penetrate the firewall with the Mixture
and Prop cables through a common penetration fitting.
Good luck,
Dick Jordan
RV 8A Finishing
N888BZ (Reserved)
----- Original Message -----
From: "DarrenHB" <darren@hartfree-bright.co.uk>
Subject: RV8-List: Superior engine installation
> --> RV8-List message posted by: "DarrenHB" <darren@hartfree-bright.co.uk>
>
> Hi all,
>
> Has anyone any experience of installing the XP-360 in a 8. Vans have told
> me that the FWF kit for the lycoming IO-360-MIB is ok except for the
> throttle/mixture kit where the cable is too short or the bracket won't fix
> to the composite sump. Has anyone solved this?
>
> thanks
>
> Darren
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Superior engine installation |
--> RV8-List message posted by: "Jack Blomgren" <jackanet@hotmail.com>
Darren,
If you haven't yet purchased the Superior you might wish to consider the
AeroSport Power IO-360-M2 (180hp). I just installed Van's IO throttle &
mixture bracket kit with perfect fit to their aluminum sump.
Jack
(Your query snipped)
http://toolbar.msn.click-url.com/go/onm00200415ave/direct/01/
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Heat Muff over exhaust joint |
--> RV8-List message posted by: "Jack Blomgren" <jackanet@hotmail.com>
Any history of heat muff(s) placed over (enclosing) joints in Vetterman
exhausts?
Any detectable CO in the cockpit?
Jack
http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|