Today's Message Index:
----------------------
1. 02:24 PM - Request special fuel fittings installation procedure. (Vincent S. Himsl)
2. 02:28 PM - Permatex anti-sieze vs fuel lube (Vincent S. Himsl)
3. 03:40 PM - Re: Permatex anti-sieze vs fuel lube (JOHN STARN)
4. 04:07 PM - Re: Request special fuel fittings installation procedure. (JOHN STARN)
5. 06:17 PM - Re: Request special fuel fittings installation procedure. (Vincent S. Himsl)
6. 09:52 PM - Re: Request special fuel fittings installation procedure. (Dick DeCramer)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Request special fuel fittings installation procedure. |
Does anyone have the correct installation procedure for the special fuel
fittings with the embedded o-ring, washer and jam? Specifically for the
following:
KB-045
KB-090-T
AEL74070
I can find no reference to these fittings and the archives show that this
question has been asked, but no one has answered.
Thanks!
Vince Himsl
RV8-SB Finish
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Permatex anti-sieze vs fuel lube |
I have been using the Permatex anit-sieze compound on my AN- threads. One of
my carburetor fittings says use 'fuel lube'. Is there a 'significant'
difference between the two?
Thanks!
Vince H.
RV8-SB Finsih
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Permatex anti-sieze vs fuel lube |
Yes.........put a small smudge of Permatex on a piece of scrap. Take
some fuel & see if you remove ANY of it. You don't need to try this with
fuel lube. It does not come off. Find you local EAA Chapter, attend a
meeting & ask of someone there will sell you a small bit. It doesn't
take much, we have the original assembly & 5 conditional inspections
from a "dab" that 1/3 filled a 35mm film case.
P.S. We still way more than 1/2 of the original "dab" left, it's not
pipe dope but it WORKS.
KABONG HRII N561FS Do Not Archive
----- Original Message -----
From: Vincent S. Himsl
To: rv8-list@matronics.com
Sent: Sunday, March 11, 2007 2:27 PM
Subject: RV8-List: Permatex anti-sieze vs fuel lube
I have been using the Permatex anit-sieze compound on my AN- threads.
One of my carburetor fittings says use 'fuel lube'. Is there a
'significant' difference between the two?
Thanks!
Vince H.
RV8-SB Finsih
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Request special fuel fittings installation procedure. |
Not sure of that you are using. A/S has Aeroquip hose & fittings but no
AEL74079 listed on pages #121, 122 and assembly instructions on 123 &
more fittings on 124. Went via Yahoo for KB-045 and was directed to A/S
site www.aircraftspruce.com/catalog/eppages/nla/contlycfuelpump.
Sorry I was not of more help. KABONG HRII N561FS Do Not Archive
----- Original Message -----
From: Vincent S. Himsl
To: rv8-list@matronics.com
Sent: Sunday, March 11, 2007 2:23 PM
Subject: RV8-List: Request special fuel fittings installation
procedure.
Does anyone have the correct installation procedure for the special
fuel fittings with the embedded o-ring, washer and jam? Specifically for
the following:
KB-045
KB-090-T
AEL74070
I can find no reference to these fittings and the archives show that
this question has been asked, but no one has answered.
Thanks!
Vince Himsl
RV8-SB Finish
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Request special fuel fittings installation procedure. |
AEL 74070
Link: http://www.eci2fly.com/pages/products_detail.aspx?in=677
Came with aerosport 0-360
KB fittings are similar but from VAN's Aircraft
_____
From: owner-rv8-list-server@matronics.com
[mailto:owner-rv8-list-server@matronics.com] On Behalf Of JOHN STARN
Sent: Sunday, March 11, 2007 4:07 PM
Subject: Re: RV8-List: Request special fuel fittings installation procedure.
Not sure of that you are using. A/S has Aeroquip hose & fittings but no
AEL74079 listed on pages #121, 122 and assembly instructions on 123 & more
fittings on 124. Went via Yahoo for KB-045 and was directed to A/S site
www.aircraftspruce.com/catalog/
<http://www.aircraftspruce.com/catalog/eppages/nla/contlycfuelpump>
eppages/nla/contlycfuelpump.
Sorry I was not of more help. KABONG HRII N561FS Do Not Archive
----- Original Message -----
From: Vincent S. Himsl <mailto:vhimsl@adelphia.net>
Sent: Sunday, March 11, 2007 2:23 PM
Subject: RV8-List: Request special fuel fittings installation procedure.
Does anyone have the correct installation procedure for the special fuel
fittings with the embedded o-ring, washer and jam? Specifically for the
following:
KB-045
KB-090-T
AEL74070
I can find no reference to these fittings and the archives show that this
question has been asked, but no one has answered.
Thanks!
Vince Himsl
RV8-SB Finish
href="http://www.matronics.com/Navigator?RV8-List">http://www.matronics.com/
Navigator?RV8-List
href="http://forums.matronics.com">http://forums.matronics.com
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Request special fuel fittings installation procedure. |
Vince...
The fitting you have, AEL74070, is a Lycoming part manufactured by ECI. The other
parts you listed are versions of the same part, one at a 90 degree with a
tee fitting and the other a 45 degree and they are for the Lycoming fuel pump
which does NOT have a tapered pipe thread like AN fittings do. These parts have
threads which are straight and as such do not seal when tightened like a pipe
thread does therefore the lock nut with a washer and a seal are provided.
These parts are adapters that go from straight threads to a flared fitting which
then can use the AN fittings. They are listed in the Lycoming parts manuals.
The fuel pump has a straight threaded hole and the surface should be faced
flat to accept the washer/seal arrangement. Just screw in one of these fittings,
90 or 45 degree as you require, with the neck facing the direction you need
for your fuel line and then wrench down the lock nut to hold the elbow and
at the same time sealing the fitting to the pump face
. Use some fuel lube on the seal. I believe the KB-090-T is a 90 degree elbow
with a tee fitting to accommodate a fitting for a fuel pressure sender.
Dick DeCramer
RV6 N500DD
200 hours
Northfield, MN
----- Original Message -----
From: Vincent S. Himsl
Sent: 3/11/2007 8:34:12 PM
Subject: RE: RV8-List: Request special fuel fittings installation procedure.
AEL 74070
Link: http://www.eci2fly.com/pages/products_detail.aspx?in=677
Came with aerosport 0-360
KB fittings are similar but from VANs Aircraft
From: owner-rv8-list-server@matronics.com [mailto:owner-rv8-list-server@matronics.com] On Behalf Of JOHN STARN
Sent: Sunday, March 11, 2007 4:07 PM
Subject: Re: RV8-List: Request special fuel fittings installation procedure.
Not sure of that you are using. A/S has Aeroquip hose & fittings but no AEL74079 listed on pages #121, 122 and assembly instructions on 123 & more fittings on 124. Went via Yahoo for KB-045 and was directed to A/S site www.aircraftspruce.com/catalog/eppages/nla/contlycfuelpump.
Sorry I was not of more help. KABONG HRII N561FS Do Not Archive
----- Original Message -----
From: Vincent S. Himsl
Sent: Sunday, March 11, 2007 2:23 PM
Subject: RV8-List: Request special fuel fittings installation procedure.
Does anyone have the correct installation procedure for the special fuel fittings
with the embedded o-ring, washer and jam? Specifically for the following:
KB-045
KB-090-T
AEL74070
I can find no reference to these fittings and the archives show that this question
has been asked, but no one has answered.
Thanks!
Vince Himsl
RV8-SB Finish
href="http://www.matronics.com/Navigator?RV8-List">http://www.matronics.com/Navigator?RV8-List
href="http://forums.matronics.com">http://forums.matronics.com
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|