Today's Message Index:
----------------------
 
     1. 04:19 AM - FS: MT Prop Governor (Neal George)
     2. 08:47 PM - Effectiveness of Van's Eyeball (LED) Cockpit Lights (Garey Wittich)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
04:19:13 AM PST US
From: 
"Neal George" <neal.george@mchsi.com>
Subject: 
FS:  MT Prop Governor
      
      For Sale:
      New MT P-860-4 Prop Governor.
      For rear-mount on (I)O-320 or (I)O-360 engines.
      $1050, shipped.
      
      
      Neal E. George 
      2023 Everglades Drive 
      Navarre, FL 32566 
      Home - 850-515-0640 
      Cell - 850-218-4838 
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
08:47:59 PM PST US
From: 
Garey Wittich <gareywittich2000@yahoo.com>
Subject: 
Effectiveness of Van's Eyeball (LED) Cockpit Lights
      
      
      Planning my Instrument Panel and need your
      "experienced" advice.
      
      Has anybody mounted these lights - one on F804N-L and
      another on F804N-R to be used as a general utility
      light (map light) ?????.   These will be mounted on
      the "upper" portion of both F804N's, near the canopy
      rail - which is angled down.
      
      Plan to use the 2 of them simultaneously (one on each
      side of the cockpit).  Is a Dimming Pot actually
      required to vary the light intensity or would just a
      Toggle Sw be adequate (OFF or ON) which would only
      give ONE brightness level (Full Bright) for night use
      ????
      
      If you have used 2 of them simulatneously with a
      Dimming Pot, what value did you use ???
      
      Since I do not have one to experiment with:
        a)  Is there an internal resistor inside the Eyeball
      Assy or is an 
             "external" resistor required for current
      limiting ???
        b)  Do the Instruction Sheet give any info on
      Voltage and Current 
             requirements for the LED ??
      
      Thank you,  Garey Wittich   Santa Monica, CA
      
      
             
      http://smallbusiness.yahoo.com/webhosting 
      
      








Other Matronics Email List Services




Post A New Message
  
rv8-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/RV8-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/rv8-list
Browse RV8-List Digests
  
http://www.matronics.com/digest/rv8-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --