Today's Message Index:
----------------------
1. 06:25 AM - Re: Fuel Tank Nutplates (Carl Bell)
2. 04:55 PM - Two New Lists Added to the Matronics Lineup! (Matt Dralle)
3. 06:13 PM - Re: Fuel Tank Nutplates (RAY SHEFFIELD)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Fuel Tank Nutplates |
Just carefully squeeze the rivets in the nutplates and you shouldn't have a
problem. CJ
_____
From: owner-rv8-list-server@matronics.com
[mailto:owner-rv8-list-server@matronics.com] On Behalf Of
JAPhillipsGA@aol.com
Sent: Friday, March 28, 2008 11:22 PM
Subject: RV8-List: Fuel Tank Nutplates
Fellow RV Builders, I'm about to remove my wings for storage until painting,
but before I put them up I want to rivet in the nutplates that hold the root
farings on. Should these holes at the edge of the tanks be dimpled or
countersunk ? Seem like they are pretty close to the Proseal and I'd hate to
make a leak. What does everybody else do ? Thanks, Bill of Georgia
**************
Create a Home Theater Like the Pros. Watch the video on AOL Home.
(http://home.aol.com/diy/home-improvement-eric-stromer?video=15&ncid=aolhom0
0030000000001)
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Two New Lists Added to the Matronics Lineup! |
Dear Listers,
I've added two new Email Lists to the Matronics List and Forum lineup today. These
include the Rans-List and RV12-List. Please surf over to the Matronics List
Subscription page and sign up for these new Lists if they are of interest
to you:
http://www.matronics.com/subscribe
Full support on the Forums, List Browse, Archives, etc. is available.
Rans-List:
http://www.matronics.com/Navigator?Rans-List
RV12-List
http://www.matronics.com/Navigator?RV12-List
Best regards,
Matt Dralle
Matronics Email List Administrator
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Fuel Tank Nutplates |
Hi Carl,
Use #6 screws, 3/8 dia 3/32 dimple die, and #6 dimple die with flat on sides
to clear tank edges. Pro seal doesn't harden completely ,so the dimpling
shouldn't
cause leaking.
ray
On Sat, Mar 29, 2008 at 9:23 AM, Carl Bell <carlbell@gforcecable.com> wrote:
> Just carefully squeeze the rivets in the nutplates and you shouldn't have
> a problem. CJ
> ------------------------------
>
> *From:* owner-rv8-list-server@matronics.com [mailto:
> owner-rv8-list-server@matronics.com] *On Behalf Of *JAPhillipsGA@aol.com
> *Sent:* Friday, March 28, 2008 11:22 PM
> *To:* rv8-list@matronics.com
> *Subject:* RV8-List: Fuel Tank Nutplates
>
>
> Fellow RV Builders, I'm about to remove my wings for storage until
> painting, but before I put them up I want to rivet in the nutplates that
> hold the root farings on. Should these holes at the edge of the tanks be
> dimpled or countersunk ? Seem like they are pretty close to the Proseal and
> I'd hate to make a leak. What does everybody else do ? Thanks, Bill of
> Georgia
>
>
> **************
> Create a Home Theater Like the Pros. Watch the video on AOL Home.
> (
> http://home.aol.com/diy/home-improvement-eric-stromer?video=15&ncid=aolhom00030000000001)
>
>
> * *
>
> * *
>
> **
>
> **
>
> **
>
> **
>
> **
>
> **
>
> **
>
> *http://www.matronics.com/contribution*
>
> * *
>
> *
>
> *
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|