Today's Message Index:
----------------------
 
     1. 12:09 PM - empennage rear spar riveting (Emmanuel QUAESAET)
     2. 05:12 PM - Re: empennage rear spar riveting (William Slaughter)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
12:09:33 PM PST US
From: 
"Emmanuel QUAESAET" <emmanuel.quaesaet@wanadoo.fr>
Subject: 
empennage rear spar riveting
      
      Hello
      
      I have just begun to build an RV8, and I am experiencing my first 
      problem.
      So that's a beginner question:
      I have tried several times to set one of the rivet assembling HS-702 
      with HS-404 and HS-405.
      Now the hole is too big and I can not set the rivet.
      Is there any solution? (the rivet is an AN-470 AD-4)
      
      Thank you very much for your answers.
      
      Emmanuel.
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
05:12:33 PM PST US
From: 
"William Slaughter" <william_slaughter@att.net>
Subject: 
empennage rear spar riveting
      
      First, get a rivet squeezer to use instead of the rivet gun. Select an over
      length rivet, and gently "pre-squeeze" it to make it swell slightly in
      diameter until you achieve a decent fit in the hole. Trim to length as
      required, then squeeze. Use the squeezer everywhere you can.
      
      
      William Slaughter
      
      RV-8 Fuselage almost finished.
      
      
      From: owner-rv8-list-server@matronics.com
      [mailto:owner-rv8-list-server@matronics.com] On Behalf Of Emmanuel QUAESAET
      Sent: Sunday, May 31, 2009 2:04 PM
      Subject: RV8-List: empennage rear spar riveting
      
      
      Hello
      
      
      I have just begun to build an RV8, and I am experiencing my first problem.
      
      So that's a beginner question:
      
      I have tried several times to set one of the rivet assembling HS-702 with
      HS-404 and HS-405.
      
      Now the hole is too big and I can not set the rivet.
      
      Is there any solution? (the rivet is an AN-470 AD-4)
      
      
      Thank you very much for your answers.
      
      
      Emmanuel.
      
      








Other Matronics Email List Services




Post A New Message
  
rv8-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/RV8-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/rv8-list
Browse RV8-List Digests
  
http://www.matronics.com/digest/rv8-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --