Today's Message Index:
----------------------
1. 03:45 PM - ()
2. 08:01 PM - Jacking Point (Matt Dralle)
3. 08:07 PM - Lubing The Tail Wheel Fork Bearing... (Matt Dralle)
4. 09:08 PM - Re: Jacking Point (donkeyvet@aol.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I had always assumed that the reason most people took off without flaps
is that the recommended flap speed of 100 is attained so quickly that
they need to be retracted almost imediatly, but don't see why you
couln't if you were right on the ball.
Mark Rose
RV8A 137MR
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Okay, so I'm sure this has been asked a few times already, and I should search
the archive, but what the heck, let's start a new thread.
I got my new tires today (Goodyear Custom Flight III, btw. Super sweet.) and started
looking for ways to get them on. I can really only see two ways to jack
the plane up easily with a normal jack.
1) I could put a short saw horse under the wing tie down and then put a hydraulic
jack on it and lift the side of the airplane up by this point. If I just gently
lift the plane by hand at this point, it seems like that's an awful lot
of weight to be lifting that far out on the wing. Can the spars really handle
this?
2) I could put a saw horse under the lower engine mount bolt to the firewall and
use a hydraulic jack to lift the plane up. This seems less scary, but I question
the shear strength of the bolt lifting all of the weight by this single
point.
What's the convential wisdom on jacking a tail dragger RV-8 to change the tires?
There has to be a way with out building some elaborate dolphin contraption.
BTW, with regards to my tire wear, since there's a fair amount of camber(?) afforded
by the Grove gear, I've got nearly all the wear on the outside 50% of the
tread. I could probably rotate them 180 degrees and get another 70 hours of
flight time, which wouldn't be bad for 22-year old stock kit tires from Van's
(remember, I swiped them from the RV-4 project after the brake incident). But,
I probably should have rotated them a bit sooner. While there's not cord showing,
the tread is gone. Live and learn; I'll be rotating these GYCFIII's in
a more timely manner. If I can double my wear life by rotating because of the
camber, I might get 1000 hours out of these babies! ;-)
Matt Dralle
RV-8 #82880 N998RV
http://www.mattsrv8.com - Matt's RV-8 Construction Blog
http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel
Status: Enjoying The Fruits of 2500 Hours of Labor!
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Lubing The Tail Wheel Fork Bearing... |
How the heck do you lube the bronze bearing on the tailwheel fork short of taking
the giant nut off. I lubed it up good during initial assembly, then at about
40 hours, it started to kind of stick, so I dissembled and lubed it again.
Now at 70 its doing it again. I foolishly put a Zerk fitting in the body of
the thing, thinking that next time I could just shoot some lube in there. Great
idea except that it doesn't work for such a tight fit.
Is there some "super lube" you can get that will last forever? I've used both
graphite wheel bearing grease and Aeroshell #6 grease.
Thanks!
Matt Dralle
RV-8 #82880 N998RV
http://www.mattsrv8.com - Matt's RV-8 Construction Blog
http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel
Status: Enjoying The Fruits of 2500 Hours of Labor!
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Jacking Point |
Matt,
I modified a tall Harbor Freight hydraulic jack at the top to accomodate
a screwed in tie-down ring. Tall enough to nix the saw horse. Seems to wo
rk great. Seems like a 6g wing can handle some gentle jacking at that poin
t. Chock all of the wheels. E-mail me @ donkeyvet@aol.com if you want a pi
cture of the modification. Dennis Flosi
-----Original Message-----
From: Matt Dralle <dralle@matronics.com>
Sent: Wed, Jun 30, 2010 8:59 pm
Subject: RV8-List: Jacking Point
kay, so I'm sure this has been asked a few times already, and I should sea
rch
he archive, but what the heck, let's start a new thread.
I got my new tires today (Goodyear Custom Flight III, btw. Super sweet.)
and
tarted looking for ways to get them on. I can really only see two ways to
jack
he plane up easily with a normal jack.
1) I could put a short saw horse under the wing tie down and then put a
ydraulic jack on it and lift the side of the airplane up by this point.
If I
ust gently lift the plane by hand at this point, it seems like that's an
awful
ot of weight to be lifting that far out on the wing. Can the spars really
andle this?
2) I could put a saw horse under the lower engine mount bolt to the firewa
ll and
se a hydraulic jack to lift the plane up. This seems less scary, but I
uestion the shear strength of the bolt lifting all of the weight by this
single
oint.
What's the convential wisdom on jacking a tail dragger RV-8 to change the
tires?
here has to be a way with out building some elaborate dolphin contraption.
BTW, with regards to my tire wear, since there's a fair amount of camber(?
)
fforded by the Grove gear, I've got nearly all the wear on the outside 50%
of
he tread. I could probably rotate them 180 degrees and get another 70 hou
rs of
light time, which wouldn't be bad for 22-year old stock kit tires from Van
's
remember, I swiped them from the RV-4 project after the brake incident).
But,
probably should have rotated them a bit sooner. While there's not cord
howing, the tread is gone. Live and learn; I'll be rotating these GYCFIII
's in
more timely manner. If I can double my wear life by rotating because of
the
amber, I might get 1000 hours out of these babies! ;-)
att Dralle
V-8 #82880 N998RV
ttp://www.mattsrv8.com - Matt's RV-8 Construction Blog
ttp://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel
tatus: Enjoying The Fruits of 2500 Hours of Labor!
-========================
========================
===========
-= - The RV8-List Email Forum -
-= Use the Matronics List Features Navigator to browse
-= the many List utilities such as List Un/Subscription,
-= Archive Search & Download, 7-Day Browse, Chat, FAQ,
-= Photoshare, and much much more:
-
-= --> http://www.matronics.com/Navigator?RV8-List
-
-========================
========================
===========
-= - MATRONICS WEB FORUMS -
-= Same great content also available via the Web Forums!
-
-= --> http://forums.matronics.com
-
-========================
========================
===========
-= - List Contribution Web Site -
-= Thank you for your generous support!
-= -Matt Dralle, List Admin.
-= --> http://www.matronics.com/contribution
-========================
========================
===========
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|