Today's Message Index:
----------------------
1. 02:55 PM - Fuel vent modification (Carl Froehlich)
2. 09:46 PM - Re: Re: RV8-List Digest: 1 Msgs - 04/26/12 (Dennis Fox)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Fuel vent modification |
Here is a simple way to keep mud-dabbers from clogging your fuel vent.
I
think more than one RV has collapsed a fuel tank from a clogged vent.
Take a few inches of 3/8=94 aluminum tubing, cut one end at 45 degrees
or so,
then JB Weld on a piece of aluminum window screen material. Once the JB
Weld is cured, clean up the edge on a ScotchBrite wheel or similar. Do
a =BE=94
cut in the other end for a hose clamp, then slide this over the now
somewhat
shortened standard =BC=94 vent tubing. Have the =BC=94 tubing extend
well past
where the clamp goes.
Carl
RV-8A (800 hours)
RV-10 (FSDO comes to inspect May 23rd)
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV8-List Digest: 1 Msgs - 04/26/12 |
thanks for the reply. Will ponder this for a while.
From: Carl Froehlich
Sent: Friday, April 27, 2012 7:38 PM
Subject: RE: RV8-List: Re: RV8-List Digest: 1 Msgs - 04/26/12
The RV-10 nose gear is the same size as the 8A main gear =93 and
in my opinion way too big for the 8A. I=99ve landed my 8A on many
grass strips without a problem.
Carl
RV-8A (800 hrs)
RV-10 (FSDO comes May 23rd for sign off)
From: owner-rv8-list-server@matronics.com
[mailto:owner-rv8-list-server@matronics.com] On Behalf Of Dennis Fox
Sent: Friday, April 27, 2012 9:14 PM
Subject: Re: RV8-List: Re: RV8-List Digest: 1 Msgs - 04/26/12
yes that was my thinking, I have an angle valve IO-360, so little extra
weight up front.
My home airport is paved, but several in the area are grass, and not
quite so smooth as pavement.
Wondering if the RV10 nose fork might be compatible but I don=99t
know what size of tire it uses.
From: Speedy11@aol.com
Sent: Friday, April 27, 2012 4:03 AM
Subject: RV8-List: Re: RV8-List Digest: 1 Msgs - 04/26/12
I haven't heard of one, but I've often wondered about it. It would
require quite a bit of work.
Do you want it for soft fields?
Stan Sutterfield
In a message dated 4/27/2012 3:03:40 A.M. Eastern Daylight Time,
rv8-list@matronics.com writes:
I would like a little larger nose wheel than the standard. Anyone
know
it this has been done before?
href="http://www.matronics.com/Navigator?RV8-List">http://www.matronics
.com/Navigator?RV8-Listhref="http://forums.matronics.com">http://forums
.matronics.comhref="http://www.matronics.com/contribution">http://www.m
atronics.com/c
http://www.matronics.com/Navigator?RV8-Listhttp://forums.matronics.comhtt
p://www.matronics.com/contribution
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|