Today's Message Index:
----------------------
1. 02:54 PM - Battery Installation and Wire Routing Provisions ()
2. 05:14 PM - Re: Battery Installation and Wire Routing Provisions (Matt Dralle)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Battery Installation and Wire Routing Provisions |
I=99m looking for feedback on adding wire routing holes to F-806B
and F-807A. Specifically, I could use an additional set on the right
side so that I can route the transponder antenna cable under the floor.
I have the one set, matching the left side battery cable routing holes,
which I intend to use for ADAHRS and A/P pitch servo cable wire routing.
I=99m planning 1 ea. 5/8=9D dia. hole in F-806B at
2.5=9D outboard of the rudder cable hole and just outboard of the
F-813R-1 Seat Rib in F-807. Van=99s has no comment. Guess the
builder mod=99s here have been too many and varied to analyze each
one. I=99m more than willing to go on past experience.
Also question re battery installation. I=99m going with an O-360
and 3-bladed Catto prop, so I think a forward battery makes sense. Was
looking at the lower right side of the baggage compartment, but that
looks next to impossible in a QB. Has anyone else done that?
Thanks in advance for any and all comments.
Stan Loer
RV-8 QB
stazel@cpros.com
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Battery Installation and Wire Routing Provisions |
At 02:53 PM 8/25/2012 Saturday, you wrote:
>Im looking for feedback on adding wire routing holes to F-806B and F-807A. Specifically,
I could use an additional set on the right side so that I can route
the transponder antenna cable under the floor. I have the one set, matching
the left side battery cable routing holes, which I intend to use for ADAHRS and
A/P pitch servo cable wire routing. Im planning 1 ea. 5/8 dia. hole in F-806B
at 2.5 outboard of the rudder cable hole and just outboard of the F-813R-1
Seat Rib in F-807. Vans has no comment. Guess the builder mods here have been
too many and varied to analyze each one. Im more than willing to go on past
experience.
>
>Also question re battery installation. Im going with an O-360 and 3-bladed Catto
prop, so I think a forward battery makes sense. Was looking at the lower
right side of the baggage compartment, but that looks next to impossible in a
QB. Has anyone else done that?
>
>Thanks in advance for any and all comments.
>
>Stan Loer
>RV-8 QB
>stazel@cpros.com
Hi Stan,
The RV-8 is really setup nice for a rear battery installation. Works out very
nicely. My RV-8, while it does have a Hartzell CS prop, its REALLY nose heavy,
especially flying solo. If you're going with an IO360, I think you're still
going to be fine with a rear mounted battery even if you go with a lighter Catto
prop. I wish I could put TWO batteries back there... ;-)
Matt
-
Matt Dralle
RV-8 #82880 N998RV "Ruby Vixen"
http://www.mattsrv8.com - Matt's Complete RV-8 Construction Log
http://www.mattsrv8.com/Mishap - Landing Mishap Rebuild Log
http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel
Status: 172+ Hours TTSN - Rebuilding Fuselage After Landing Mishap...
RV-6 #20916 N360EM "The Flyer"
http://www.mattsrv6.com - Matt's RV-6 Revitalization Log
Status: 118+ Hours Since Purchase - Upgrades Complete; Now In Full Flyer Mode
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|