Today's Message Index:
----------------------
1. 01:00 PM - Re: Need RV-8 empennage inventory sheet (Rasmussen, Robert CAPT USFF, N7)
2. 06:38 PM - Re: Gear Tower Covers (Mike Koehn)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Need RV-8 empennage inventory sheet |
This might be helpful to RV-8 builders...
-----Original Message-----
From: owner-rv8-list-server@matronics.com [mailto:owner-rv8-list-server@matronics.com] On Behalf Of Matt Dralle
Sent: Monday, March 11, 2013 22:45
Subject: Re: RV8-List: Need RV-8 empennage inventory sheet
At 03:46 PM 3/10/2013 Sunday, you wrote:
>--> <n223rv@wolflakeairport.net>
>
>Does anyone have an RV-8 empannage inventory sheet they can email me? Old or
new are fine.
>
>Thank you!
>
>-Mike Kraus
>RV-4 sold :-(
>RV-10 flying :-)
>KitFox SS7 Radial building :-)
Hi Mike,
Here you go. Here is a PDF scan of the sheets from my RV-8 kit circa 2008.
Matt
-
Matt Dralle
RV-8 #82880 N998RV "Ruby Vixen"
http://www.mattsrv8.com - Matt's Complete RV-8 Construction Log http://www.mattsrv8.com/Mishap - Landing Mishap Rebuild Log
http://www.youtube.com/MattsRV8 - Matt's RV-8 HDTV YouTube Channel
Status: 172+ Hours TTSN - Rebuilding Fuselage After Landing Mishap...
RV-6 #20916 N360EM "The Flyer"
http://www.mattsrv6.com - Matt's RV-6 Revitalization Log
Status: 140+ Hours Since Purchase - Upgrades Complete; Now In Full Flyer Mode
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Gear Tower Covers |
Got Pictures or a drawing? That is about my next job on my QB 8. Saw a
mod years ago on the board that looked pretty good but I believe it is a
two cover version. Yours may be much better.
Regards,
Mike Koehn
DogTick
From: owner-rv8-list-server@matronics.com
[mailto:owner-rv8-list-server@matronics.com] On Behalf Of
stazel@cpros.com
Sent: Monday, March 18, 2013 2:54 PM
Subject: RV8-List: Gear Tower Covers
I=99ve cut out each gear tower lower web in my QB fuselage and
plan to install 0.063 thick covers, but a bit different from what I have
seen. I am curious as to whether anyone else has done this and/or if
I=99m missing something which would make this a bad idea. My
covers will have cutouts matching the lower half of the middle hole and
upper half of the lower hole. Essentially a very exaggerated
=9CH=9D. The overall dimensions are
4.13=9Dx7=9D. Each plate will install with 16 #8 machine
screws, probably AN525=99s, and AN365 nuts. The primary advantage
I see is that this eliminates all the nutplates required with full
covers. Also, the holes will be preserved for inspection purposes and
in the unlikely event that any maintenance or servicing at all can be
done through them. All feedback greatly appreciated.
Stan Loer
RV-8 QB
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|