Today's Message Index:
----------------------
1. 09:35 AM - Doghouse Quality (Leland)
2. 10:03 AM - F774skin / F732B bracket / F632A channel - tipper builders only. (Steve Sampson)
3. 01:03 PM - Slider canopy paint (Roy Taylor)
4. 08:23 PM - Re: F774skin / F732B bracket / F632A channel - tipper builders only. (Gary)
5. 09:57 PM - Re: Doghouse Quality (Dr. Leathers)
Message 1
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Doghouse Quality |
--> RV9-List message posted by: "Leland" <RV9AQB@frys.com>
The sheet aluminum part C-792 that I received with the slider finishing kit
was badly bent. I talked to Tom Green who sent me a new part but he said
that it would not be much better. He was right, it isn't. This part fits on
top of the fuselage, behind the slider canopy and is shown on Drawing 41. It
is called the "dog house". Has anyone had good luck at making a new one or
straightening out the old part?
Leland in Pleasanton
Working on wheel pants (The main gear fairings and wheel pants parts are
high quality and only require cutting and sanding)
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | F774skin / F732B bracket / F632A channel - tipper builders only. |
--> RV9-List message posted by: "Steve Sampson" <SSampson.SLN21@london.edu>
I'm sorry guys - me again. I don't want to be obtuse but I cant for the life
of me figure out the junction of the above parts. DWG 39 & 40.
Are the 3/32 skin rivets meant to go through the skin / bulkhead flange,
F732B bracket and F632A channel?
If YES - then the rivet callout is wrong, and it is not indicated this way
on the plans.
If NO - then there is nowhere for the shopheads to go. They will have to go
at least through the F732B.
Also, a related question. How far from the bulkhead is the rear edge of the
the F632A channel? It appears about 3/16th or " on view D-D Dwg40, but I
can not find it defined.
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Slider canopy paint |
--> RV9-List message posted by: "Roy Taylor" <Royandjilly@btinternet.com>
Thanks Dave,
Roy
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: F774skin / F732B bracket / F632A channel - tipper builders |
only.
--> RV9-List message posted by: "Gary" <rv9er@3rivers.net>
Steve......this is one of the things I tried to explain in that long email about
Tip-up stuff. It is hard to describe until you start putting the stuff together.
I think the best solution is like you say.....use long rivets through the whole
works. The drawings do not acknowlege the problem, so don't try to follow them
on that point. Also, I long ago stopped paying much attention to rivet length
callouts. I use my homemade length gage instead.
My rollover brace channel F-732A just fits up against the bulkhead at the top.
I don't think it matters if you want to leave a little gap.
Gary
----- Original Message -----
From: Steve Sampson
To: rv9-list@matronics.com
Sent: Wednesday, January 01, 2003 11:20 AM
Subject: RV9-List: F774skin / F732B bracket / F632A channel - tipper builders
only.
--> RV9-List message posted by: "Steve Sampson" <SSampson.SLN21@london.edu>
I'm sorry guys - me again. I don't want to be obtuse but I cant for the life
of me figure out the junction of the above parts. DWG 39 & 40.
Are the 3/32 skin rivets meant to go through the skin / bulkhead flange,
F732B bracket and F632A channel?
If YES - then the rivet callout is wrong, and it is not indicated this way
on the plans.
If NO - then there is nowhere for the shopheads to go. They will have to go
at least through the F732B.
Also, a related question. How far from the bulkhead is the rear edge of the
the F632A channel? It appears about 3/16th or " on view D-D Dwg40, but I
can not find it defined.
---
Version: 6.0.431 / Virus Database: 242 - Release Date: 12/18/02
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Doghouse Quality |
--> RV9-List message posted by: "Dr. Leathers" <DrLeathers@822heal.com>
Hi Leland,
Please explain further. Am I getting this straight? Van's sent you a
defective or damaged part with your kit. You called and spoke to Tom about
the problem. Tom told you he would send a replacement part, but forewarned
you that the replacement part would also be damaged or defective?? What am I
missing here?
DOC
Do not archive
----- Original Message -----
From: "Leland" <RV9AQB@frys.com>
Subject: RV9-List: Doghouse Quality
> --> RV9-List message posted by: "Leland" <RV9AQB@frys.com>
>
> The sheet aluminum part C-792 that I received with the slider finishing
kit
> was badly bent. I talked to Tom Green who sent me a new part but he said
> that it would not be much better. He was right, it isn't. This part fits
on
> top of the fuselage, behind the slider canopy and is shown on Drawing 41.
It
> is called the "dog house". Has anyone had good luck at making a new one or
> straightening out the old part?
> Leland in Pleasanton
> Working on wheel pants (The main gear fairings and wheel pants parts are
> high quality and only require cutting and sanding)
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|