Today's Message Index:
----------------------
1. 12:57 PM - RV-9A Silhouette (Nightingale Michael)
2. 01:47 PM - Re: RV-9A Silhouette (Andy Karmy)
3. 04:52 PM - Re: RV-9A Silhouette (fcs@jlc.net)
4. 10:09 PM - Clamp for nose strut fairing (Gary)
5. 10:22 PM - Clamps for nose strut fairing (Gary)
Message 1
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | RV-9A Silhouette |
--> RV9-List message posted by: "Nightingale Michael" <NightingaleMichaelV@JohnDeere.com>
I'm looking for side and top silhouettes to start working on a paint scheme.
Michael V. Nightingale
DEERE & Co. Computer Center
400 19th ST.
Moline, IL. 61265
pager 563-327-7891
nightingalemichael@johndeere.com
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV-9A Silhouette |
--> RV9-List message posted by: "Andy Karmy" <andy@karmy.com>
RV8 builder Bill VonDane has them all on his website...
http://www.vondane.com/paint/index.htm
- Andy
---------- Original Message ----------------------------------
From: "Nightingale Michael" <NightingaleMichaelV@JohnDeere.com>
>--> RV9-List message posted by: "Nightingale Michael" <NightingaleMichaelV@JohnDeere.com>
>
>I'm looking for side and top silhouettes to start working on a paint scheme.
>
>Michael V. Nightingale
>DEERE & Co. Computer Center
>400 19th ST.
>Moline, IL. 61265
>
>pager 563-327-7891
>
>nightingalemichael@johndeere.com
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: RV-9A Silhouette |
--> RV9-List message posted by: "fcs@jlc.net" <fcs@jlc.net>
They're also included in the finish kit plans.
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Clamp for nose strut fairing |
--> RV9-List message posted by: "Gary" <rv9er@3rivers.net>
Andy,
Yeah, mine is done........except for finding the specified 3/8 inch wide hose clamp.
I was just going to post a message on the list about this, to see what
solutions people had.
The problem is not the pant.....it is the clamp. The deal is, the only hose clamps
I can find in a big enough size to go around the nose strut and fairing are
all 1/2 inch wide. Vans calls out a 3/8 inch wide clamp. I called Van's
on this, after searching all the hardware stores, and the aircraft supply catalogs.
The only place I have not checked is McMaster-Carr.
Van's didn't have an answer, other than what I'd already tried. He said it shouldn't
be a problem to find narrow hose clamps. I said, fine, you guys find them,
and include them in the kit.
Bottom line is, the pant and fairing fit fine, we just need a clamp that is narrow
enough and has a small enough worm drive so it won't hit the inside of the
front of the nose pant when the gear pivots.
I'll post this to the two lists and see what we stir up.
Gary
----- Original Message -----
From: Andy Karmy
To: rv9er@3rivers.net
Sent: Thursday, January 16, 2003 4:05 PM
Subject: Nose wheel pant?
Hey Gary,
I'm having a hard time getting the nosewheel pant to work out. Have you fit that
part yet? I finished mounting the pant and everything was fine until I tried
to install the nose gear leg fairing. Seems the hoseclamp at the bottom is
too high (when pressed all the way down) so it apears that I got the pant mounted
too low (by about 3/16") so now I can't hide the clamp inside the pant...
Did yours work out, or have you done it yet?
- Andy
---
Version: 6.0.431 / Virus Database: 242 - Release Date: 12/22/02
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Clamps for nose strut fairing |
--> RV9-List message posted by: "Gary" <rv9er@3rivers.net>
Andy......looks like McMaster Carr can help us out. They have 5/16 inch wide
stainless hose clamps all the way up past 2 inches. The 1 1/4 inch size is around
$5 for a package of ten.
Go to http://www.mcmaster.com/ and search for hose clamps, worm drive.
Gary
---
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|