---------------------------------------------------------- RV9-List Digest Archive --- Total Messages Posted Mon 03/24/03: 18 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 06:15 AM - Re: Wing jig question (david edgemon) 2. 07:39 AM - leading edge installation (JOHN KERR) 3. 08:23 AM - Re: leading edge installation (BFlood@sauer-danfoss.com) 4. 10:17 AM - Re: Wing Jig Question (fcs@jlc.net) 5. 10:18 AM - Re: leading edge installation (fcs@jlc.net) 6. 11:11 AM - horizontal stabilizer riveting (Bruce Anthony) 7. 11:36 AM - Re: horizontal stabilizer riveting (Ken Moak) 8. 12:17 PM - Re: leading edge installation (Gary) 9. 02:31 PM - Re: leading edge installation (Curt Hoffman) 10. 02:46 PM - Re: Wing Jig Question (Curt Hoffman) 11. 04:39 PM - Re: leading edge installation (Tom Lutgring) 12. 05:33 PM - Re: Wing Help (Mike Duiven) 13. 05:36 PM - Re: leading edge installation (John Oliveira) 14. 05:42 PM - Re: Re: Wing jig question (John Oliveira) 15. 08:20 PM - FW: Wing Jig Question (Todd Houg) 16. 08:24 PM - Re: Wing Jig Question (DThomas773@aol.com) 17. 08:32 PM - Re: horizontal stabilizer riveting (DThomas773@aol.com) 18. 08:33 PM - Re: leading edge installation (Todd Houg) ________________________________ Message 1 _____________________________________ Time: 06:15:22 AM PST US From: david edgemon Subject: RV9-List: Re: Wing jig question --> RV9-List message posted by: david edgemon Ken, Since I just finished the wings I'll give you my two cents worth. Wings really pretty light. My wife and I could lift it really easily. Maybe 50 lbs or so a panel. (just a guess). Put the wings as far apart as you need to get a cordless drill (screwdriver) and screws between the wings. Don't ask how I know this. Put them as low as you can and still assemble the rear spar and hinges. Maybe 6 inches off the floor for the rear spar would be could. This will make working on the tanks, landing lights, etc... easier. Plus at some point you'll want to flight them and work on the rear spar area for hinges. Definately do both at once. It's much faster to do the second set of operations since you just did the first ones. Have fun. > > >>1. About how heavy is a wing? >> >>2. About how far off the uprights do you place the >>spar? I am making it movable much like Todd Houg >>shows on his WEB site. I have a cross member running >>between my uprights and need to determine how much >>space I need to get between the wing and the cross >>member. >> >>3. About how high off the floor did you put the spar? >> I know this would depend on the person, but a general >>idea would be nice >> >>4. I would like to hang both wings at once, any >>comments? >> >> >> >> -- David Edgemon Summit Research Corp. Huntsville Al. _______ | \__________________(*)__________________/ "NN" Huntsville Soaring Club ________________________________ Message 2 _____________________________________ Time: 07:39:26 AM PST US From: JOHN KERR Subject: RV9-List: leading edge installation --> RV9-List message posted by: JOHN KERR for those of you who have finished attaching the leading edge to the spar...how does one with out and extra elbow get to the rivets attaching the 4th rib from the tip to the spar. It is the one between the most inboard lightening (small)hole and the aileron bellcrank. ________________________________ Message 3 _____________________________________ Time: 08:23:39 AM PST US Subject: Re: RV9-List: leading edge installation From: BFlood@sauer-danfoss.com 03/24/2003 10:21:25 AM --> RV9-List message posted by: BFlood@Sauer-Danfoss.com Very Carefully. JOHN KERR To: rv9 -list Sent by: cc: owner-rv9-list-server@mat Subject: RV9-List: leading edge installation ronics.com 03/24/2003 09:34 AM Please respond to rv9-list --> RV9-List message posted by: JOHN KERR for those of you who have finished attaching the leading edge to the spar...how does one with out and extra elbow get to the rivets attaching the 4th rib from the tip to the spar. It is the one between the most inboard lightening (small)hole and the aileron bellcrank. ________________________________ Message 4 _____________________________________ Time: 10:17:18 AM PST US From: "fcs@jlc.net" Subject: Re: RV9-List: Wing Jig Question --> RV9-List message posted by: "fcs@jlc.net" I agree with everything Larry says, except I would build BOTH wings at the same time. This is easily done if you build your jig so it carries both wings and leaves some room in between. The wings are light enough that I could lift them off and turn them around when working on the opposite side. The reason I say to do both, is for project enthusiasm. Finishing a big project like a wing, then facing doing it all over for the other one, can really knock the wind out of your sails. Doing them both at once means less tool and mindset changing. And when you're done, you're DONE! I don't have a really good photo of the jig I used, but all I did was modify the "H" jig used to build the empennage by adding a couple of cross-members to hang the wing spars on. The following photo will give you the general idea. I continued to use this jig all the way through building and aligning the control surfaces, which I also built upright, attached to the hinges. http://www.jlc.net/~fcs/images/wing/w_rearspar.jpg ________________________________ Message 5 _____________________________________ Time: 10:18:45 AM PST US From: "fcs@jlc.net" Subject: RE: RV9-List: leading edge installation --> RV9-List message posted by: "fcs@jlc.net" That's a favorite one. Everyone who has done this, will recall the nearly bloody red rings around their forearms. Basically you have to develop that third elbow you described, or if your arms are just too big, enlist a competent smaller person to help. ________________________________ Message 6 _____________________________________ Time: 11:11:04 AM PST US Subject: RV9-List: horizontal stabilizer riveting From: "Bruce Anthony" --> RV9-List message posted by: "Bruce Anthony" Need some advice on riveting a nose rib in a 9A horizontal stabilizer. I put in the end ribs first to give the stabilizer some form, but now that I'm trying to rivet in the middle rib, I get a depression deformation in the skin right at the rib. How do I avoid this? Should I drill out the end ribs and do the middle one first? Would clecoing in the forward spar help? Thanks. Bruce Anthony RV9A Horizontal Stabilizer ________________________________ Message 7 _____________________________________ Time: 11:36:35 AM PST US From: Ken Moak Subject: Re: RV9-List: horizontal stabilizer riveting --> RV9-List message posted by: Ken Moak Bruce Welcome to the club. When the spar is out it can take some odd shapes. A depression gave me fits. There is a real good explanation in the archives by I think John Williams, may be on the Yahoo groups. I drilled and worked on one side of mine so much I had to go to oversized rivets so be careful. I don't remember putting in the end ribs that soon. Some things that helped for me 1. Put the wood clamps close to the center rib. 2. Start at the nose. 3. Do the top first. If it is going to act up try and get it on the bottom. 4. I made shims for my worse side, .040 (i think) and cover all but the most forward hole. Never got mine looking as good as I would like. Tech guy did not think it was a problem. If I was to do it again I think it would be better but I was about to start buying a skins so I decided I could live with it. Ken 90608 Starting Wings Today! --- Bruce Anthony wrote: > --> RV9-List message posted by: "Bruce Anthony" > > > Need some advice on riveting a nose rib in a 9A > horizontal stabilizer. I put in the end ribs first > to give the stabilizer some form, but now that I'm > trying to rivet in the middle rib, I get a > depression deformation in the skin right at the > rib. How do I avoid this? Should I drill out the > end ribs and do the middle one first? Would > clecoing in the forward spar help? Thanks. > > > Bruce Anthony > RV9A Horizontal Stabilizer > > > > Contributions > any other > Forums. > > latest messages. > List members. > > http://www.matronics.com/subscription > http://www.matronics.com/FAQ/RV9-List.htm > Digests:http://www.matronics.com/digest/rv9-list > http://www.matronics.com/archives > http://www.matronics.com/photoshare > http://www.matronics.com/emaillists > > > > > http://platinum.yahoo.com ________________________________ Message 8 _____________________________________ Time: 12:17:03 PM PST US From: "Gary" Subject: Re: RV9-List: leading edge installation --> RV9-List message posted by: "Gary" Not quite all of us. Some of us used blind rivets in a few of those holes, and still have the use of our arms. Gary ----- Original Message ----- From: fcs@jlc.net To: rv9-list@matronics.com Sent: Monday, March 24, 2003 11:17 AM Subject: RE: RV9-List: leading edge installation --> RV9-List message posted by: "fcs@jlc.net" That's a favorite one. Everyone who has done this, will recall the nearly bloody red rings around their forearms. Basically you have to develop that third elbow you described, or if your arms are just too big, enlist a competent smaller person to help. --- Version: 6.0.462 / Virus Database: 261 - Release Date: 3/15/03 ________________________________ Message 9 _____________________________________ Time: 02:31:44 PM PST US From: "Curt Hoffman" Subject: Re: RV9-List: leading edge installation --> RV9-List message posted by: "Curt Hoffman" There was some discussion a while back on use of blind rivets, special bucking bars, etc. I even talked to Vans to get their thoughts on use of blind rivets and such. Their advise was basically "Just Do it". So I did. Fortunately I had good help on the gun while I held my trustly little Avery bar which is about 3" x 1" x2". Ultimately is is doable and other than a few red marks on your arms, once you get in there all the rivets are reachable. I am average size and my arms fit ok. I couldn't see all the rivets I was bucking but I could feel them. I started with the ones I could see so we got into a rythem on how long to take. It actually came out quite good and I didn't use any blind rivets. Curt Hoffman RV-9A wings done for now- working on tail 1968 Mustang 302 convertible Piper Cherokee N5320W ----- Original Message ----- From: "JOHN KERR" Subject: RV9-List: leading edge installation > --> RV9-List message posted by: JOHN KERR > > > for those of you who have finished attaching the leading edge to the > spar...how does one with out and extra elbow get to the rivets > attaching the 4th rib from the tip to the spar. It is the one between > the most inboard lightening (small)hole and the aileron bellcrank. > > ________________________________ Message 10 ____________________________________ Time: 02:46:20 PM PST US From: "Curt Hoffman" Subject: Re: RV9-List: Wing Jig Question --> RV9-List message posted by: "Curt Hoffman" Given the responses this seems to be an area of personal preference. So here's mine: I built both wings at once with the jigs set up end to end- I have a long basement. I left room between the two jigs to walk between but barely. I set up the supports so that the spar was about neck high. I could then mount my ailerons and flaps while still in the jig. The only problem I ran into was I had one set or uprights slightly closer together than the other and when I mounted the flap the end couldn't quite clear the upright. Not a big deal but annoying. I would make the uprights as far apart as I could which would be about 3" less than the length of the spar. Making both at the same time was definitely a plus. Many jobs were good to do together. Some are boring enough that I was afraid if I didn't do them at the same time I'd never get up the energy to do the other. Having said that it was a little hard to get the energy up to go to the basement when I knew all I would be doing is deburring holes for the next 6 hours. My wife and I moved the wings off the jog and laid down on the workbench and ultimately into my roll around support. I agree they aren't all that heavy but they sure are big. Curt Hoffman RV-9A wings done for now- working on tail 1968 Mustang 302 convertible Piper Cherokee N5320W ----- Original Message ----- From: "Ken Moak" Subject: RV9-List: Wing Jig Question > --> RV9-List message posted by: Ken Moak > > Thanks to everyone that helped me with the empennage. > A Technical Counselor (Jim) came out last week and the > first milestone has happened. No rework, so I closed > things up. Thanks to all the advise, either direct or > in the archives. > > Now I'm starting the Wing and have a couple of > questions. > > 1. About how heavy is a wing? > > 2. About how far off the uprights do you place the > spar? I am making it movable much like Todd Houg > shows on his WEB site. I have a cross member running > between my uprights and need to determine how much > space I need to get between the wing and the cross > member. > > 3. About how high off the floor did you put the spar? > I know this would depend on the person, but a general > idea would be nice > > 4. I would like to hang both wings at once, any > comments? > > Any advice would be appreciated. > > Ken > 90608 > Building the wing jig > > http://platinum.yahoo.com > > ________________________________ Message 11 ____________________________________ Time: 04:39:43 PM PST US Subject: Re: RV9-List: leading edge installation From: Tom Lutgring --> RV9-List message posted by: Tom Lutgring John , Yeah those leading edge to spar rivets are tricky. The one you describe has a small lightening hole next to it. The four center rivets can easily be squeezed with a Tatco squeezer with 3" jaws. I would imagine most brands would work. I squeezed all of the rib to spar rivets that have lightening holes next to them. The few that could not be reached (upper and bottom most rivets at small lightening hole location only) I used blind rivets on. Vans support okayed the use of LP4-3 or cherrymax rivets. Tom, Ohio RV-9A fuselage ________________________________ Message 12 ____________________________________ Time: 05:33:07 PM PST US From: "Mike Duiven" Subject: Re: RV9-List: Wing Help --> RV9-List message posted by: "Mike Duiven" 90517's Kit had the holes mismatched too. Mike N711ED (Reserved) ----- Original Message ----- From: "The Strong's" Subject: Re: RV9-List: Wing Help > --> RV9-List message posted by: "The Strong's" > > This is interesting. My kit number is #90489 and those holes are still > mismatched. I guess Van's just likes to make > sure they will have a few easy questions to answer. > > > Tom (working on wings) > > > > > > ________________________________ Message 13 ____________________________________ Time: 05:36:53 PM PST US From: "John Oliveira" Subject: Re: RV9-List: leading edge installation --> RV9-List message posted by: "John Oliveira" Small hands. Was not really a problem, but that was a year ago ----- Original Message ----- From: "JOHN KERR" Subject: RV9-List: leading edge installation > --> RV9-List message posted by: JOHN KERR > > > for those of you who have finished attaching the leading edge to the > spar...how does one with out and extra elbow get to the rivets > attaching the 4th rib from the tip to the spar. It is the one between > the most inboard lightening (small)hole and the aileron bellcrank. > > > > > > > ________________________________ Message 14 ____________________________________ Time: 05:42:03 PM PST US From: "John Oliveira" Subject: Re: RV9-List: Re: Wing jig question --> RV9-List message posted by: "John Oliveira" I did my wings much as described. Rear spar about 18 inches off of the floor. I then flipped them over to do the lower skins so I was reaching up after I attached all the hinge brackets and the gap fairings. I could then attach and adjust the ailerons mounted facing up. The instructions talk about doing the lower skins while on the bench, but it worked very well doing the skins vertically in the fixture. John Oliveira N909RV, 90054 Wings and empennage done - Fuselage on it's way. ----- Original Message ----- From: "david edgemon" Subject: RV9-List: Re: Wing jig question > --> RV9-List message posted by: david edgemon > > Ken, > Since I just finished the wings I'll give you my two cents worth. > > Wings really pretty light. My wife and I could lift it really easily. > Maybe 50 lbs or so a panel. (just a guess). > > Put the wings as far apart as you need to get a cordless drill (screwdriver) > and screws between the wings. Don't ask how I know this. > > Put them as low as you can and still assemble the rear spar and hinges. > Maybe 6 inches off the floor for the rear spar would be could. This will > make working on the tanks, landing lights, etc... easier. Plus at some > point you'll want to flight them and work on the rear spar area for hinges. > > Definately do both at once. It's much faster to do the second set of > operations > since you just did the first ones. > > Have fun. > > > > > > >>1. About how heavy is a wing? > >> > >>2. About how far off the uprights do you place the > >>spar? I am making it movable much like Todd Houg > >>shows on his WEB site. I have a cross member running > >>between my uprights and need to determine how much > >>space I need to get between the wing and the cross > >>member. > >> > >>3. About how high off the floor did you put the spar? > >> I know this would depend on the person, but a general > >>idea would be nice > >> > >>4. I would like to hang both wings at once, any > >>comments? > >> > >> > >> > >> > -- > > David Edgemon > Summit Research Corp. > Huntsville Al. > > > _______ > | > \__________________(*)__________________/ > "NN" > Huntsville Soaring Club > > ________________________________ Message 15 ____________________________________ Time: 08:20:21 PM PST US From: Todd Houg Subject: FW: RV9-List: Wing Jig Question --> RV9-List message posted by: Todd Houg Hello Ken, In response to your posted questions as well as your direct inquiry . . . I would estimate that each wing complete with skins weighs somehwere around 80 lbs each +/- 20, maybe less with no ailerons, flaps or 150 clecos attached! I have moved the wings by myself, but I prefer not to. My wife can easily handle one end when I need to swap them around. My wing jig has 36" base legs with the uprights 2/3 offset to one side, leaving 12" to center on one end and 24" to center on the other. My intention was to build a jig that would hold one wing, thus the offset would keep the weight centered when I has the wing on. When I mounted the angle supports for the spar I had extra material so I decided to extend them on the short side of the uprights. This worked out quite well, since the wing jig is quite stable with both wings on it. If I'm working with one wing it's always on the long side. The jig is still stable with one wing on the short side, but I still put some bags of lead shot on the base legs while I'm swapping wings around. If I were planning for two wings, I would probably move the uprights to the center of the base legs and still use 36" legs. This would still give eighteen inches of leg on either side, and the spar supports don't need to extend any more than twelve inches from the upright. I mounted my spar supports about shoulder height. This work out quite well, but I wouldn't want them any higher. A little lower than shoulder height would work OK also. I made two wood self like supports on one wall so I could remove one wing from the jig and hang it on the wall out of the way. This worked great, you just have to swap them arouns once in a while. My lower cross memeber between the uprights is about 24" off the floor. Mine is positioned just below the level of the rear spar although itcould be higher since the wing is offset from the uprights. With it below the rear spar I was able to put support block under the rear spar to remove the sag when fitting the skins. Let me know if you have any more questions . . . Todd RV9A fuselage - temporarily stalled . . . -----Original Message----- From: Ken Moak [SMTP:ken_moak@yahoo.com] Subject: RV9-List: Wing Jig Question --> RV9-List message posted by: Ken Moak Thanks to everyone that helped me with the empennage. A Technical Counselor (Jim) came out last week and the first milestone has happened. No rework, so I closed things up. Thanks to all the advise, either direct or in the archives. Now I'm starting the Wing and have a couple of questions. 1. About how heavy is a wing? 2. About how far off the uprights do you place the spar? I am making it movable much like Todd Houg shows on his WEB site. I have a cross member running between my uprights and need to determine how much space I need to get between the wing and the cross member. 3. About how high off the floor did you put the spar? I know this would depend on the person, but a general idea would be nice 4. I would like to hang both wings at once, any comments? Any advice would be appreciated. Ken 90608 Building the wing jig http://platinum.yahoo.com ________________________________ Message 16 ____________________________________ Time: 08:24:47 PM PST US From: DThomas773@aol.com Subject: Re: RV9-List: Wing Jig Question --> RV9-List message posted by: DThomas773@aol.com Larry, You are absolutely right. I would not attempt to move a wing without a good sturdy person on the other end of it. It is just too long and wide to handle alone. Dennis Thomas ________________________________ Message 17 ____________________________________ Time: 08:32:56 PM PST US From: DThomas773@aol.com Subject: Re: RV9-List: horizontal stabilizer riveting --> RV9-List message posted by: DThomas773@aol.com Hi Bruce, This is a problem we have all had. I just accepted the depression, or pillowing as some call it. It is caused by the skin not being uniformly held to the shape needed and you actually are squeezing the skin in to meet the rib. Some folks say they have overcome it by adding additional cradles to your jig. I'm sure you will get addtional advice as well. Dennis Thomas fuselage ________________________________ Message 18 ____________________________________ Time: 08:33:20 PM PST US From: Todd Houg Subject: RE: RV9-List: leading edge installation --> RV9-List message posted by: Todd Houg Find a friend with long skinny arms! My arms are too fat to fit back there, but fortunately my friend and neighbor had the perfect long skinny arms. If that's not an option, others have used pop rivets, but make sure you use the structural cherrymax rivets of you go that route. Good luck, Todd Houg -----Original Message----- From: JOHN KERR [SMTP:kerrjohna@comcast.net] Subject: RV9-List: leading edge installation --> RV9-List message posted by: JOHN KERR for those of you who have finished attaching the leading edge to the spar...how does one with out and extra elbow get to the rivets attaching the 4th rib from the tip to the spar. It is the one between the most inboard lightening (small)hole and the aileron bellcrank. eJ8+Ii0EAQaQCAAEAAAAAAABAAEAAQeQBgAIAAAA5AQAAAAAAADoAAEIgAcAGAAAAElQTS5NaWNy b3NvZnQgTWFpbC5Ob3RlADEIAQ2ABAACAAAAAgACAAEEkAYAtAEAAAEAAAAQAAAAAwAAMAIAAAAL AA8OAAAAAAIB/w8BAAAASwAAAAAAAACBKx+kvqMQGZ1uAN0BD1QCAAAAAHJ2OS1saXN0QG1hdHJv bmljcy5jb20AU01UUABydjktbGlzdEBtYXRyb25pY3MuY29tAAAeAAIwAQAAAAUAAABTTVRQAAAA AB4AAzABAAAAFwAAAHJ2OS1saXN0QG1hdHJvbmljcy5jb20AAAMAFQwBAAAAAwD+DwYAAAAeAAEw AQAAABkAAAAncnY5LWxpc3RAbWF0cm9uaWNzLmNvbScAAAAAAgELMAEAAAAcAAAAU01UUDpSVjkt TElTVEBNQVRST05JQ1MuQ09NAAMAADkAAAAACwBAOgEAAAAeAPZfAQAAABcAAABydjktbGlzdEBt YXRyb25pY3MuY29tAAACAfdfAQAAAEsAAAAAAAAAgSsfpL6jEBmdbgDdAQ9UAgAAAABydjktbGlz dEBtYXRyb25pY3MuY29tAFNNVFAAcnY5LWxpc3RAbWF0cm9uaWNzLmNvbQAAAwD9XwEAAAADAP9f AAAAAAIB9g8BAAAABAAAAAAAAAJpXgEEgAEAKAAAAFJFOiBSVjktTGlzdDogbGVhZGluZyBlZGdl IGluc3RhbGxhdGlvbgCwDQEFgAMADgAAANMHAwAYABYAHgAUAAEAPgEBIIADAA4AAADTBwMAGAAW ABwAFwABAD8BAQmAAQAhAAAARjVDNEJFMUMxMDNDQTg0MUFEOTk5QTA1REEzNjI4MjQANgcBA5AG ALgIAAAhAAAACwACAAEAAAALACMAAAAAAAMAJgAAAAAACwApAAAAAAADAC4AAAAAAAMANgAAAAAA QAA5AKAY6D6H8sIBHgBwAAEAAAAoAAAAUkU6IFJWOS1MaXN0OiBsZWFkaW5nIGVkZ2UgaW5zdGFs bGF0aW9uAAIBcQABAAAAFgAAAAHC8oc+4NasnTAZ3E+Rr+Gv3DSya9EAAB4AHgwBAAAABQAAAFNN VFAAAAAAHgAfDAEAAAAUAAAAdGhvdWdAYXR0Z2xvYmFsLm5ldAADAAYQRvHLHQMABxDaBgAAHgAI EAEAAABlAAAARklOREFGUklFTkRXSVRITE9OR1NLSU5OWUFSTVNNWUFSTVNBUkVUT09GQVRUT0ZJ VEJBQ0tUSEVSRSxCVVRGT1JUVU5BVEVMWU1ZRlJJRU5EQU5ETkVJR0hCT1JIQURUSEVQRQAAAAAC AQkQAQAAAJAFAACMBQAAgQoAAExaRnUFPGe4PwAKAQMB9wKkA+MCAGNowQrAc2V0MCAHEwKDQwBQ DuZwcnEyD+Z9EwqACMggOwlvMjU1SwKACoF2CJB3awuAZNo0DGBjAFALA2MAQQtgQG5nMTAzMwum IOJGFMEgYSADUAiQFxExA/B0aCAJABYAIHMJFLFueRcwcm1zIQcF0BjEGNFlIHRvbz0XUGEFQBoA F1AX4CBilQDQaxnwaASQZSwa4E51BUACEAAgdW4aUGV6bBjAbRjAF2UAcBcgbvBlaWdoBuAFwA9w FyDpG0EgcASQZgWQBUAYLrAuIElmGzEaUCcEIKxubwVAA5FvBTBpAiBfG5Ag8BtRBCAPcHYZ4HVr D6AXIHAhUCAFECJgdNZzG5QAwGsZ4HMIcBngjnkIYCKCHlNzdHIVELUcIHIHQCAPYASQcgbAvGF4 IxUhQCBQJIJnGiDvIHIjEAhgHGAuCqIKhAqA3kcaEBcgCkAbECwoVQGRrCBUBHAXIEgIYGcoWuEK 9GxpMzYBQBWgAUAPETAg8B7hEHQxNiAttS2yTwUQZwuAJcFNB5Dwc2FnZS2zKFYsxCyRgwsTLMZp LTE0NAFA8SwQMTgwAUAM0DFTKkAqRgNhOgyDYg/QSk8ASE4gS0VSUiDAW1NNVFA6JAAmIChqb2gc QEAFoG1jymElQC4dkHRdKFUqQBcGYAIwMudNAiBkYXmNG5BNCsAPYCAyNBuQgwHQFjAgOTozNA/g jk011ypgMudydjktoMcsECVANdh1Ymoe4TLnoFJWOS1MOrE6HxC+ZR4wC4AYUAmALuAgC4D/JUAH QAtgIXIvXzBqLBQLtvsoYy2wPjxnHKAupCLRJUDZIrFieTzwM3g8NH81gv4+Kv4KgBvxGzFDABng JwXed0cgIjQasAMAcxtQFyH7AkAA0Gg9Uh5iPRsagR5idShUcwqxLkvARyAH4GR+bweRAiAZ4BfT KAEdQ2X+eCVQF0AccAbgB+Au4Bpj7x5iJpUoVEkMNBfxBRAqQL8DUh5TIXAjAEq1S4MgIDCvBUAE AB5TTIJiD7B3CeH/SxUeYgRgQkELgAbgCxEfEM8dsRxgAwAYQShzAMA+MP4pRyA9EB1DHmILcD0Q A2DfA6BTwD4wBQAAcGsoSyhUeF8tPVoPWx9cL10/PXdZh1LAXvotKlAecUHnResAwAMRRgWwdVFg L0Vewn9f8FMRG/FhUVMRS4ACIHP3BbAisTZxaQlwHIEX8Cfx/x3AHlMIUAIwUPEbwCGBDzC/Xncn AUIlBtAiAVKxWQhg/ic+MB2BImAFwA+gU6EAcP8dkAXAHjAm4WjxGLEh015o/xvxUWAnAT1ACXAe 8R4waCH/IXAAkBhBV/EeYjewJVACIPxpYwQgYSMgEFmPbu9v/xdxD13PXtEhGSBORVfXSKFzUV5o QgNgdyTRPLR8IFUk0SSBBcBT8CpAYv9000bxGiAUch8QHFFCSG3JrCBQRyAagVMPcWV1ce95cx6Q eSIEICYaoT0QBCD/TMQbQmacbe99z37ff+9yLzte0UIjUhxwHFEXIElu92qyPllew1BU8i6VdXE6 UW06k0CDYW0ELjURXmlVAE4vU1VCU0NSGElCRXVxVeB0cDqoLy93iNAuhfsvJDCOYgT0g5xCI0ZB UXVxb17yiG+JdouxLzx2S+B094a6BmA3w0UWAAuAebGMX8eJd4+jXmk3LUQ3cHS1d4g/iUl2dC+F Zl5pdMVE8x2wd6FzOpQfiXY9QJfS/5YPXuEHEElBImCYEIv/iRz/N8KbooPKeSucT4lnelR5gvWK vlMeoGMGkG0wkG+JWPuaP1LAT3unm9Oj34l2ZwD/V6E6op5aZQujv4lYBaBlKP98z66vr7+wz4EO so9GCxHxAgC1AAMAEBAAAAAAAwAREAAAAAADAIAQ/////0AABzDgDRz5hvLCAUAACDDgDRz5hvLC AQsAAIAIIAYAAAAAAMAAAAAAAABGAAAAAAOFAAAAAAAAAwACgAggBgAAAAAAwAAAAAAAAEYAAAAA EIUAAAAAAAADAAWACCAGAAAAAADAAAAAAAAARgAAAABShQAAtw0AAAMACYAIIAYAAAAAAMAAAAAA AABGAAAAAAGFAAAAAAAAHgATgAggBgAAAAAAwAAAAAAAAEYAAAAAVIUAAAEAAAAEAAAAOC4wAAsA F4AIIAYAAAAAAMAAAAAAAABGAAAAAA6FAAAAAAAAAwAYgAggBgAAAAAAwAAAAAAAAEYAAAAAEYUA AAAAAAADABqACCAGAAAAAADAAAAAAAAARgAAAAAYhQAAAAAAAB4AKYAIIAYAAAAAAMAAAAAAAABG AAAAADaFAAABAAAAAQAAAAAAAAAeACqACCAGAAAAAADAAAAAAAAARgAAAAA3hQAAAQAAAAEAAAAA AAAAHgArgAggBgAAAAAAwAAAAAAAAEYAAAAAOIUAAAEAAAABAAAAAAAAAB4APQABAAAABQAAAFJF OiAAAAAAAwANNP03AAB6Yg==