Today's Message Index:
----------------------
1. 06:34 AM - Re: Match Drilling question (Mike Hoover)
2. 09:10 AM - Re: Match Drilling question (fcs@jlc.net)
3. 03:50 PM - re drilling hs ribs to spar (MICK MULLER)
4. 08:23 PM - Re: re drilling hs ribs to spar (robert watson)
Message 1
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Match Drilling question |
--> RV9-List message posted by: "Mike Hoover" <mikehoover@sc.rr.com>
Pete,
If I remember, I just pushed the main rib at enough angle to get the drill
into place. If you have two clecoes in and drill the remaining hole you
should be able to do this easily. If you bend the main rib flag, just bend
it back. If you do not have a Souix air drill, you might think very
seriously about getting one.
Hope this helps.
Mike
SC
90709 (put deposit on wing kit)
----- Original Message -----
From: "Pete Howell" <pete.howell@gecko-group.com>
Subject: RV9-List: Match Drilling question
> --> RV9-List message posted by: "Pete Howell"
<pete.howell@gecko-group.com>
>
> Hi There,
>
> New builder here. I am match drilling my HS ribs and spars. How do I
match
> drill the nose/main rib/ front spar combo? I can't get my drill in there
> square to do it. Is there a trick, or is it OK to be out of square a bit?
> There is a good chance I am missing something basic. I am using a small
> cordless drill if that makes a difference.
>
> Thanks,
>
> Pete Howell
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Match Drilling question |
--> RV9-List message posted by: "fcs@jlc.net" <fcs@jlc.net>
Also, before you are done, you will need at least one, 90-degree drill
chuck attachment. Get one from Brown Tool, or Cleveland, etc. with a small
size so it fits in tight corners. Cordless drills are nice, but they tend
to be bulky.
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | re drilling hs ribs to spar |
--> RV9-List message posted by: "MICK MULLER" <MULLERPHARM@bigpond.com>
Pete,
I cheated and clecoed the nose rib to the spar without the main rib and
match drilled. Then I took off the
nose rib, clecoed the main rib and repeated the process. In both cases I was
able to easily keep the drill vertical
and thus make reasonably neat holes.
Mick Muller
> --> RV9-List message posted by: "Pete Howell"
<pete.howell@gecko-group.com>
>
> Hi There,
>
> New builder here. I am match drilling my HS ribs and spars. How do I
match
> drill the nose/main rib/ front spar combo? I can't get my drill in there
> square to do it. Is there a trick, or is it OK to be out of square a bit?
> There is a good chance I am missing something basic. I am using a small
> cordless drill if that makes a difference.
>
> Thanks,
>
> Pete Howell
>
>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: re drilling hs ribs to spar |
--> RV9-List message posted by: robert watson <bob1629r@earthlink.net>
-------Original Message-------
From: MICK MULLER <MULLERPHARM@bigpond.com>
Subject: RV9-List: re drilling hs ribs to spar
> Use Long Bit 12" Helps with angel.
> --> RV9-List message posted by: "MICK MULLER" <MULLERPHARM@bigpond.com>
Pete,
I cheated and clecoed the nose rib to the spar without the main rib
and
match drilled. Then I took off the
nose rib, clecoed the main rib and repeated the process. In both cases I
was
able to easily keep the drill vertical
and thus make reasonably neat holes.
Mick Muller
> --> RV9-List message posted by: "Pete Howell"
<pete.howell@gecko-group.com>
>
> Hi There,
>
> New builder here. I am match drilling my HS ribs and spars. How do I
match
> drill the nose/main rib/ front spar combo? I can't get my drill in
there
> square to do it. Is there a trick, or is it OK to be out of square a
bit?
> There is a good chance I am missing something basic. I am using a small
> cordless drill if that makes a difference.
>
> Thanks,
>
> Pete Howell
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|