RV9-List Digest Sat 07/12/03

RV9-List Digest Archive

Sat 07/12/03

Total Messages Posted: 3



Today's Message Index:
----------------------
 
     1. 05:18 PM - Tip Up Canopy (DThomas773@aol.com)
     2. 05:28 PM - Re: Tip Up Canopy (Jim Brandvold)
     3. 05:29 PM - Re: Tip Up Canopy (DThomas773@aol.com)
 
 
 

Message 1


					NEXT  Skip to NEXT Message
	LIST  Reply to LIST Regarding this Message
		SENDER  Reply to SENDER Regarding this Message

      
      
Time: 05:18:00 PM PST US
From: DThomas773@aol.com
Subject: Tip Up Canopy      
      --> RV9-List message posted by: DThomas773@aol.com
      
      Hi Folks,
      A question to those who have already been there.  I'm just starting to trim 
      the big bubble.  How far do you go on the initial cut?  I see the mold marks 
      around the perimeter and assume these have to go.  Is this a good guide line for
      
      the first slice?
      
      Dennis Thomas
      Canopy
      
      
      
      
      
      

Message 2


					INDEX  Back to Main INDEX
				PREVIOUS  Skip to PREVIOUS Message
					NEXT  Skip to NEXT Message
	LIST  Reply to LIST Regarding this Message
		SENDER  Reply to SENDER Regarding this Message

      
      
Time: 05:28:16 PM PST US
From: "Jim Brandvold" <jbrandv@worldnet.att.net>
Subject: Tip Up Canopy      
      --> RV9-List message posted by: "Jim Brandvold" <jbrandv@worldnet.att.net>
      
      That is where we started.  Remember to sand the edges even if you have
      more to take off.  That way there is less chance of getting a crack
      started.
      
      Jim Brandvold
      N209RV (Reserved)
      Setting wing incidence angle.
      
      -----Original Message-----
      From: owner-rv9-list-server@matronics.com
      [mailto:owner-rv9-list-server@matronics.com] On Behalf Of
      DThomas773@aol.com
      Subject: RV9-List: Tip Up Canopy
      
      
      --> RV9-List message posted by: DThomas773@aol.com
      
      Hi Folks,
      A question to those who have already been there.  I'm just starting to
      trim 
      the big bubble.  How far do you go on the initial cut?  I see the mold
      marks 
      around the perimeter and assume these have to go.  Is this a good guide
      line for 
      the first slice?
      
      Dennis Thomas
      Canopy
      
      
      direct advertising on the Matronics Forums.
      
      
      
      
      
      

Message 3


					INDEX  Back to Main INDEX
				PREVIOUS  Skip to PREVIOUS Message
					NEXT  Skip to NEXT Message
	LIST  Reply to LIST Regarding this Message
		SENDER  Reply to SENDER Regarding this Message

      
      
Time: 05:29:59 PM PST US
From: DThomas773@aol.com
Subject: Re: Tip Up Canopy      
      --> RV9-List message posted by: DThomas773@aol.com
      
      Thanks Jim
      
      
      
      
      
      








Other Matronics Email List Services




Post A New Message    rv9-list@matronics.com
UN/SUBSCRIBE    http://www.matronics.com/subscription
List FAQ    http://www.matronics.com/FAQ/RV9-List.htm
Full Archive Search Engine    http://www.matronics.com/search
7-Day List Browse    http://www.matronics.com/browse/rv9-list
Browse RV9-List Digests    http://www.matronics.com/digest/rv9-list
Browse Other Lists    http://www.matronics.com/browse
Archive Downloading    http://www.matronics.com/archives
Photo Share    http://www.matronics.com/photoshare
Other Email Lists    http://www.matronics.com/emaillists
Contributions    http://www.matronics.com/contributions









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --