Today's Message Index:
----------------------
1. 07:48 AM - plans snafu (smbluthing@volexpress.com)
2. 09:34 AM - Re: plans snafu (Tim Coldenhoff)
3. 12:16 PM - Re: plans snafu (Dean)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> RV9-List message posted by: smbluthing@volexpress.com
dwg 28 around area d4 "see f-824B cover plate detail dwg 26"..........i
go to dwg 26 and see no cover plate detail, my dwg26 is dated
8/14/00......does anyone know where cover plate detail is on the plans
or could someone email the detail? thanking you in advance for your
assistance.
will i every finish or is the a test of patience!
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> RV9-List message posted by: Tim Coldenhoff <rv9a_000@deru.com>
smbluthing@volexpress.com wrote:
> --> RV9-List message posted by: smbluthing@volexpress.com
>
> dwg 28 around area d4 "see f-824B cover plate detail dwg 26"..........i
> go to dwg 26 and see no cover plate detail, my dwg26 is dated
> 8/14/00......does anyone know where cover plate detail is on the plans
> or could someone email the detail? thanking you in advance for your
> assistance.
Drawing 44 area e7 has F-824B cover plate hardware callouts.
--
Tim Coldenhoff
www.deru.com/~rv9a
90338 - plumbing/electrical/finishing
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> RV9-List message posted by: "Dean" <dvanwinkle@royell.net>
I have Dwg 26, rev 1, dated 3/9/01 and it has no reference to the F-824B
cover plate either. If you have the finish kit or Preview Plans, check Dwg
44, zones D7 and E7 for the installation details. There are 8 tapped holes
in each longeron for fairing installations, 6 for the F-994A empennage gap
cover and 2 for the F-994B empennage fairing. The 4 fwd holes in the F-994A
match the F-773 side skins, and the aft 2 locate the holes to be drilled
through the F-824B cover plate and longeron. The 7th hole through the
F-994B/F-824B/longeron appears to be eyeballed and the 8th hole appears to
pick up the existing rivet hole in the fwd flange of the aft tailcone
bulkhead. See the notes in zone 9E. Hope this helps.
Dean
90095 Fuselage/Finish
----- Original Message -----
From: <smbluthing@volexpress.com>
Subject: RV9-List: plans snafu
> --> RV9-List message posted by: smbluthing@volexpress.com
>
> dwg 28 around area d4 "see f-824B cover plate detail dwg 26"..........i
> go to dwg 26 and see no cover plate detail, my dwg26 is dated
> 8/14/00......does anyone know where cover plate detail is on the plans
> or could someone email the detail? thanking you in advance for your
> assistance.
>
>
> will i every finish or is the a test of patience!
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|