----------------------------------------------------------
                           RV9-List Digest Archive
                                      ---
                     Total Messages Posted Sun 01/11/04: 3
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 10:37 AM - exhaust  (Steve Sampson)
     2. 05:57 PM - Re: Looking for EAA technical advisor  (Gerry Filby)
     3. 07:35 PM - Swivel head pop riveter  (Merems)
 
 
 
________________________________  Message 1  _____________________________________


Time: 10:37:19 AM PST US
From: "Steve Sampson" <SSampson.SLN21@london.edu>
Subject: RV9-List: exhaust

--> RV9-List message posted by: "Steve Sampson" <SSampson.SLN21@london.edu>

I seem tp be getting in a tangle with somthing that ought to be simple.

There are 6 stainless tubes which slide into the three bits of rubber tube
that make the mountings for the exhaust. Can anyone give me an idea of how
long the vertical elements were (hole center to hole center) when it was all
in the right place? Did you shorten the stainless tubes to around 3" overall
from 5"? Did the horizontal mounting end up clear below the mixture cable?

Thanks, Steve.
#90360
exhaust
UK

---






________________________________  Message 2  _____________________________________


Time: 05:57:14 PM PST US
Subject: RE: RV9-List: Looking for EAA technical advisor
From: Gerry Filby <gerf@gerf.com>

--> RV9-List message posted by: Gerry Filby <gerf@gerf.com>


Thanks all for your comments - I'm going to swing by the EAA 
Chapter meeting this coming Tuesday at SQL, get started there.

Regards,
Gerry.
RV-9 #90842.

do not archive

> 
> --> RV9-List message posted by: "Bill Repucci" <bill@repucci.com>
> 
> Gary,
> 
> Have you check with your local EAA chapter?  If they can't help you,
> contact the EAA national and see who they would recommend.  Remember,
> you don't need an advisor who is or has built an RV to inspect your kit.
> 
> Good luck!
> Bill
> RV-9
> SN: 90737
> N941WR (Reserved)
> Left Wing
> 390 hours and counting
> Bla bla bla ...
> 
> -----Original Message-----
> From: owner-rv9-list-server@matronics.com
> [mailto:owner-rv9-list-server@matronics.com] On Behalf Of Gerry Filby
> To: rv9-list@matronics.com
> Subject: RV9-List: Looking for EAA technical advisor
> 
> 
> --> RV9-List message posted by: Gerry Filby <gerf@gerf.com>
> 
> 
> Hi Folks,
> 
> I'm on the Peninsula in San Francisco, got my empennage kit 
> beginning of December, getting ready to start the priming and 
> final assembly of the HS.
> 
> Can anyone recommend an EAA technical adivsor in the area that 
> would work with me once in a while ?
> 
> Regards,
> 
> Gerry.  
> RV-9 #90842.
> 
> do not archive
> 
> ========================================================== 
> Gerry Filby                                  gerf@gerf.com 
>                     Home (415) 239 4846
>                     Cell (415) 203 9177
> 
> 
> ==
> direct advertising on the Matronics Forums.
> ==
> ==
> ==
> 
> 
> 
> 
> 
> 
> 

-- 
========================================================== 
Gerry Filby                                  gerf@gerf.com 
                    Home (415) 239 4846
                    Cell (415) 203 9177






________________________________  Message 3  _____________________________________


Time: 07:35:19 PM PST US
From: "Merems" <merems@cox.net>
   <rv8list@yahoogroups.com>, <rv7-list@matronics.com>,
   <RV7and7A@yahoogroups.com>, "RV10 Group" <RV10@yahoogroups.com>
Subject: RV9-List: Swivel head pop riveter

--> RV9-List message posted by: "Merems" <merems@cox.net>

Fellow builders,

Harbor Freight has their swivel head pop riveter on sale for $4.99.  It appears
to be very good quality and for this price you can't go wrong.  If you are not
familiar with the swivel head design it is rather clever.  It allows you to
adjust "swivel" the head so that you can gain access to pop rivets in locations
where the standard pop riveter can't.


Paul Merems (RV-4/RV-7A)